Category: A-B

Description

Allen-Bradley 1785-L30B is an Allen-Bradley PLC5 controller: The Allen-Bradley 1785-L30B is an Allen-Bradley PLC5 controller. The controller has 32K words of user memory and supports 1024 (any mix) or 1024 inputs + 1024 outputs (complementary). It has embedded communication ports such as two (2) DH+/Remote I/O (adapters or scanners) and one (1) serial port that can be configured for RS-232 and 423 and RS-422A standards.

About the 1785-L30B

The 1785-L30B is an Allen-Bradley controller that is part of the PLC5 controller family. The controller has 32K words of user memory, two (2) DH+/Remote I/O combo ports that can be configured as adapters or scanners, and one (1) serial port that supports RS-232. 423. and RS-422A communication standards.

The 1785-L30B supports a large number of I/O devices. It supports up to 1024 I/O devices, which can consist of any combination of discrete and analogue I/O devices. In addition, it supports complementary 1024 input and 1024 output devices.

In addition to supporting a large number of I/O devices, the controller is also capable of implementing a www.ge-drive.com remote I/O architecture, as it can connect up to 28 remote I/O racks. To implement remote I/O architecture, integrated communication ports such as DH+ and Remote I/O (RIO) channels can be used. In addition, an Ethernet interface module can be added to realise the same architecture via an Ethernet network.

The 1785-L30B is fitted with a battery that will be available for use by the controller in the event of a power failure. The battery is used to hold user and programme data stored in the controller’s user memory. It is equipped with a BATT LED to report the current level of the battery. For the 1785-L530B, the battery will last 84 days at 100% shutdown and 150 days at 50% shutdown at an operating temperature of 60 degrees Celsius. When the BATT LED is on, the battery will continue to operate for 5 days from the first appearance of the signal. When the battery is fully depleted, the contents of the user memory will remain unchanged unless the controller is powered on. The contents of the user memory are erased only when power is lost and the battery is depleted.

The 1785-L30B has two built-in ports such as Channel 1A and Channel 1B. These ports can be configured as Remote I/O Scanners, Remote I/O Adapters, and DH+ communication interfaces. In addition, the 1785-L30B controller provides a 25-pin connector serial port interface. The serial port supports the RS232C standard and can be configured for system protocols such as ASCII and DF1. full-duplex and half-duplex master protocols, and half-duplex slave protocols. An 8-pin miniature DIN connector labelled Channel 1A is also available and also supports DH+ connectivity.

The 1785-L30B has several indicator lights on the front panel for easy interaction with the user. These indicators are labelled BATT and are used to show battery status. The indicator labelled PROC indicates the status of the controller. the FORCE indicator is used to show whether or not the I/O force is enabled. the COMM indicator is connected to channel 0 and is used to report communication activity, while channels 1A and 1B both have dedicated status indicators.

The controller has a three-position pushbutton switch to set the controller mode. Each position corresponds to one of the processor modes, such as Run, PROG, and REM In Run mode, the controller executes the program and activates the output devices PROG stops the execution of the logic and allows the controller to be configured and programmed REM executes the logic and allows configuration and programming.

The 1785-L30B has 32.000 words of memory and a battery backup. For programme backup, an EEPROM module can be installed in the front panel slot. Memory modules are available in various capacities.The total number of I/Os (including local I/O and general-purpose remote I/O combinations) is 1024 in any combination, or 1024 inputs and 1024 outputs complementary.A total of 29 I/O chassis are available for the 1785-L30B, of which 28 are general-purpose remote I/O chassis. The 1785-L30B has a backplane current load of 2.3 amps at 5 volts. 1785-L30B cannot be connected to an expansion local I/O chassis.

Allen-Bradley 1788-DNBO Description

The Allen-Bradley 1788-DNBO is a DeviceNet daughter card.

About the 1788-DNBO

The Allen-Bradley 1786-DNBO is a DeviceNet daughter card. This daughter card can be used with any Allen-Bradley device that is compatible with this module.

To configure the DeviceNet daughter card, RSNetWorx for DeviceNet V3.0 Service Pack 2 is required, which is needed to include the module in the system scan list.

To set the network address of the 1788-DNBO, the 1788-DNBO provides two (2) switches. Valid node addresses are 0-63. which is the range of nodes supported by the DeviceNet network. In general, the node address of a daughter card must be unique and there can be no duplicate addresses in the network. In addition, setting the node address to 99 and rebooting the module erases the scan table defined on the daughter card, so only do this if you need to erase the scan table. Switch settings will be read at power-up to determine the set address and expected operation of the daughter card.

The network transfer rate can be configured using another hardware switch mounted on the www.ge-drive.com daughter card. This switch is located next to the removable connector and allows you to set the speed, e.g. 125 Kb when set to zero (0), 250 Kb when set to one (1) and 500 Kb when set to two (2).

The daughter card is equipped with status indicators, such as the Network Status (NS) and I/O Status indicators. The Network Status Indicator is a two-colour LED that typically shows the status of the communication link, and the I/O Status Indicator is also a two-colour LED that shows the I/O scanning speed.

The 1788-DNBO daughter card offers selectable baud rates and nodes (0 = 125k, 1 = 250k, 2 = 500k) that can be set via the on-board hardware fader wheel, with input and output data rates of 124 double integer (DINT) and 123 DINT, respectively. 1788-DNBO daughter card connects to the DeviceNet network via the factory-supplied 5-pin DeviceNet connector cable, which connects to the DeviceNet network. The 1788-DNBO Daughter Card connects to the DeviceNet network via a factory-supplied 5-pin DeviceNet connector cable that connects to the DeviceNet port on the scanner and is tightened with the connector screws. 1788-DNBO Daughter Card has an operating temperature range of 0 to 60 degrees Celsius, a storage temperature range of -40 to 85 degrees Celsius, and a net shipping weight of 0.5 kg. The 1788-DNBO daughter card has an operating temperature range of 0 to 60 degrees Celsius, a storage temperature range of -40 to 85 degrees Celsius, a net shipping weight of 0.1 kg, and is CE, c-UR-us, C-TICK, and ODVA certified.

Description The Allen-Bradley 1769-L32E is the 1769 CompactLogix controller in the 5370 CompactLogix family. The controller has 750KB of internal memory, one (1) Ethernet and one (1) RS232 communication port. It supports up to sixteen (16) compact I/O modules and up to three (3) expansion libraries.

About the 1769-L32E

The CompactLogix Modular Controller, part number 1769-L32E, is a programmable automation controller (PAC) from Allen-Bradley. The controller is typically used in machine control and mid-size process applications. The controller incorporates one (1) RS232 and one (1) Ethernet communication port.

The default configuration for the RS232 interface is DF1 full duplex, 19.2 Kbps, no parity, station address 0. no handshaking, BCC error detection, auto-detect embedded response, 8 data bits and 1 stop bit. This default configuration can be manually configured to establish initial communication with the device. If used with RSLinx, autoconfiguration can be used to automatically detect communication settings. The RS232 port can also be configured as an ASCII protocol interface for connection to bar code instruments, typically used in manufacturing processes.

Ethernet communication requires an initial configuration, which can be done www.ge-drive.com via BOOTP-DHCP or downloaded via the RS232 interface. When using BOOTP-DHCP, an Ethernet cable is required to connect the controller to the BOOTP host.

The Allen-Bradley 1769-L32E Compact Logix Controller is available in a unique compact cost-effective package. It incorporates one (1) EtherNet and one (1) serial communication port. It can be connected to the device via a 1747-CP3 or 1756-CP3 cable or an Ethernet cable. It has 750 KB of internal user memory, which can be expanded using the CompactFlash card part number 1784-CF128.

The 1769-L32E comes with a replaceable battery, part number 1769-BA, and supports the installation of up to 16 compact I/O modules, with up to 3 I/O groups connected via 2 expansion cables. 1769-L32E has a (5 V) DC current consumption of 850 mA, and dissipates up to 6.5 watts of heat. 1769-L32E can be easily mounted using either DIN-mounting or panel-mounting. The 1769-L32E can be easily mounted in either DIN or panel mounting, with DIN mounting having an operating shock rating of 30 G and a non-operating shock rating of 50 G, and panel mounting having an operating mode shock rating of 30 G and a non-operating mode shock rating of 50 G. The 1769-L32E can be easily mounted in either DIN mounting or panel mounting.

The 1769-L32E controller has an operating mode vibration rating of 5 G. It can withstand mounting torque forces from 1.1 to 1.8 N-m. The 1769-L32E has an operating temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit), a storage temperature range of -40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit), and a non-condensing relative humidity range of 0 to 95 percent. The Logix controller has a Group 1 certified emissions (CISPA11) rating and a unique open housing. Stranded wire from 22 to 16 AWG is recommended, while solid wire should be rated from 22 to 14 AWG. The module weighs approximately 2 pounds when shipped and measures 8 x 8 x 5 inches.

The CompactLogix 1769 Series serves as a migration platform for the legacy Allen Bradley PLC family, PLC5 and SLC500. A variety of CompactLogix 1769 products, including the 1769-L32E, ensure that previous processor functionality is maintained and enhanced.

The 1769-L32E processor can accommodate up to sixteen (16) compact I/O modules. It also supports expansion by adding three (3) I/O expansion banks. The controller has 750 Kbytes of internal memory and can be connected to non-volatile memory by installing a 1784-CF64 or 1784-CF128 CompactFlash card. The controller uses the 1769-BA to retain user memory. Avoid fully discharging the batteries as this may cause the user memory (including the user programme) to be erased. Use of non-volatile memory prevents such an event.

Description: The Allen-Bradley 1336-SN-SP6A PCB or Printed Circuit Board has an output rating of 460 volts AC and 60 to 100 horsepower.

The board is compatible with Allen-Bradley D-Frame 1336 Plus, Plus II, Impact, and Force drives.

About the 1336-SN-SP6A

The Allen-Bradley 1336-SN-SP6A Inverter Buffer Board Assembly Kit is a replacement buffer board for 1336 series Allen-Bradley AC drives.

The 1336-SN-SP6A buffer board is a stand-alone device that does not share a common bus and is compatible with Impact, Force, Plus, and Plus series 1336 drives.

In general, the 1336-SN-SP6A PCB Inverter Buffer Board and all similar boards help to limit switching voltages and any rise in transient voltage levels in the circuit.

The 1336-SN-SP6A buffer board assembly kit includes 3 inverter www.ge-drive.com buffer boards and 15 included fastening screws.

Designed to be compatible with Allen-Bradley 1336 Plus, Plus II, Force, and Impact drives.

The AC input voltage is rated at 230 volts and the output power is rated at 40 to 50 horsepower.

It is also compatible with 460-volt AC D-frame drives rated at 60 to 100 horsepower.

The 1336-SN-SP6A board is available as a 575-volt AC power-rated D-Frame 1336 Plus rated between 75 and 100 horsepower,

Plus II, Force, and Impact series drives.

The 1336-SN-SP6A inverter buffer plate is not backward compatible with any previous inverter buffer plate version.

It can only be used as a replacement for a buffer plate with similar specifications. Replacing the old buffer plate and installing a new one is very simple.

To install the 1336-SN-SP6A PCB inverter buffer board, remove the case (if any) and switch off the power to the hard disc.

Remove the screws securing the old board, remove the old board, and replace it with the new board.

Description.

The 1402-LS51 is a line synchronisation module designed to be incompatible with Allen-Bradley’s 1771 PLC series.

It is a two (2) slot module with the same form factor as the 1771 series. The module measures 5 A full-scale current and 100/120 VAC.

It is primarily used to synchronise different three-phase systems, can perform engine governor control, and is used as a multi-function power metering device.

About the 1402-LS51

The Allen-Bradley 1402-LS51 is a line synchronisation module. www.ge-drive.com The module is primarily used to synchronise two (2) different three-phase systems.

The module is a two-slot module that mounts directly to Allen-Bradley’s 1771 chassis.

The 1402-LS51 provides automatic synchronisation, load sharing, and high-speed power system monitoring.

The 1402-LS51 performs voltage matching error in 0.05% steps; frequency matching error or slip in 0.01 Hz resolution; and synchronisation buses in 1 degree resolution.

Synchronisation bus and reference bus phase matching error in 1 degree resolution; and load sharing error in scalar measurements from 0.000 to +/- 1.000).

The module’s synchronisation function provides various status feedbacks such as frequency within limits; voltage within limits; phase within limits; synchronisation mode conflict fault; phase rotation mismatch fault; phase rotation mismatch fault (0.000 to +/- 1.000 scalar).

Phase rotation mismatch fault (3-phase sync mode only); No reference bus voltage fault; No sync bus voltage fault; Reference bus overvoltage fault and Sync bus overvoltage fault.

The module’s energy meter functions include a large number of measurable and calculable parameters, in particular current (amperes, per phase and neutral); average current (amperes); positive sequence current (amperes); and

Negative Sequence Current (Amps); Current Unbalance Percentage Voltage (Volts, per phase L-L, also L-N in 4-wire systems).

Average voltage (Volts, L-L, also L-N in four-wire systems); Positive-sequence voltage in Volts; Negative-sequence voltage in Volts; Percentage voltage unbalance.

Frequency in Hertz; phase rotation (ABC, ACB); power factor in per cent (total power factor, also per phase in four-wire systems).

Watts (total watts and watts per phase in a four-wire system); Volt-amperes (total volt-amperes and volt-amperes per phase in a four-wire system).

Varistors (total number of varistors and number of varistors per phase in a four-wire system); Power consumption in kWh.

reactive power consumption in kilovolt-amperes-hours; and demand (amperes, volt-amperes, and watts).

The 1402-LS51 module is a line synchronisation module manufactured by Allen-Bradley/Rockwell Automation.

The Allen-Bradley 1402-LS51 Line Synchronisation Module is a solid-state module, not a hard-wired electromechanical module, which means it is suitable for a variety of industrial applications.

However, it should not be used for safety functions that require sudden surges of power, such as emergency stops.

Attempting to use this solid-state module for emergency functions may damage the module, cause it to fail, prevent the emergency or error it was designed to respond to, or cause injury to the user.

The purpose of the Allen-Bradley 1402-LS51 Line Synchronisation Module is to synchronise two different three-phase systems through features such as load sharing, automatic synchronisation, and high-speed power system monitoring.

The Allen-Bradley 1402-LS51 Line Synchronisation Module has 2 slots for installation in a standard 1771 I/O chassis, also manufactured by Allen-Bradley.

It can be used as a multifunction digital power monitor to synchronise 2 systems.

It measures all the appropriate parameters of the two connected three-phase systems to provide the appropriate error and control signals for the synchronisation process.

It is important that the Allen-Bradley 1402-LS51 Line Synchronisation Module be installed in a dry, clean industrial environment that does not contain strong magnetic fields, strong electric fields, or sustained high heat sources.

The synchronisation module can only be used in an operating temperature range of 0 to 60 degrees Celsius. It can be mounted in a local rack to maximise data transfer rates.

Description

The Allen-Bradley 1398-DDM-075 is an Ultra 200 series digital servo drive: The Allen-Bradley 1398-DDM-075 is an Ultra 200 series digital servo drive. The servo drive is enabled when the AC input voltage requirement is 100-240VAC rms, single-phase or three-phase, and the www.ge-drive.com input frequency is 47-63 Hz. The drive has peak output currents of 50 amps (single phase input) and 75 amps (three phase input) and continuous output currents of 15 amps (single phase input) and 35 amps (three phase input). Peak output power is 14 kilowatts for single phase, 20 kilowatts for three-phase peak output, and 7.5 kilowatts for three-phase continuous output.

About the 1398-DDM-075

The Allen-Bradley 1398-DDM-075 is an Ultra 200 servo drive. This drive was one of Allen-Bradley’s early servo drive products. It is a microprocessor-based servo drive with built-in functions for managing drive current, speed, and position.Ultra 200 servo drives (such as the 1398-DDM-075) are compatible with brushless servo motors.

Specifically, the 1398-DDM-075 has an AC input voltage requirement of 100-240VAC rms, single-phase or three-phase, and an input frequency of 47-63 Hz. It also has an auxiliary input that is isolated from the supply voltage of the main AC input circuit. The auxiliary AC input is rated at 100-240 VAC, single phase, 47-63 Hz, and has an input current of 1.0 amp for 100 VAC and 0.5 amp for 240 VAC.

The drive has a peak output current of 50 amps for single-phase input and 75 amps for three-phase input, and a continuous output current of 15 amps for single-phase operation and 35 amps for three-phase operation. Peak output power is 14 kilowatts for single phase, 20 kilowatts for three-phase peak output, and 7.5 kilowatts for three-phase continuous output.

The drive has a total line voltage of 141-339 VDC, bus capacitance energy absorption of 152 Joules, and bus capacitance of 4290 µF. power dissipation is 300 watts.

The 1398-DDM-075 has five (5) user-configurable 24 Volt, current-absorbing, opto-isolated, active-high inputs; one (1) fixed assignment control (ENABLE), current-absorbing, opto-isolated, active-high input; four (4) assignable 24 Volt, current-absorbing, opto-isolated, active-high outputs; and two (2) dedicated (Brake and Drive Ready), normally open relay outputs. relay outputs. The embedded analogue input/output channels include two dedicated 10-bit 0 – 10 volt analogue inputs (+I LIMIT and -I LIMIT) and two selectable ±10 volt analogue outputs, one 12-bit and one 8-bit (ANALOG1 and ANALOG2).

The 1398-DDM-075 module also has analogue outputs with 8-bit and 12-bit resolution. The analogue input voltage range is 0-10 volts. The analogue inputs have 10-bit resolution. 1398-DDM-075 has an integrated power supply and a shunt regulator, which uses a microcontroller to manage the machine’s position, speed, and current. 1398-DDM-075 servo drives are powerful and require minimal maintenance. When maintenance is required, the standard procedure is to check that cable insulation and connections are intact. Recommended humidity limits are between 5% and 95%, the same as other ULTRA 200 drives. 1398-DDM-075 weighs 21.32 lbs. Peak output currents are 50A for single-phase power supplies and 75A for three-phase power supplies. the input frequency is 47-63 Hz. when operating the 1398-DDM-075 ULTRA 200 Servo Drive from a single-phase power supply, the current limit must be set correctly to avoid damage to the module. the 1398-DDM-075 can be operated from a single-phase power supply. the 1398-DDM-075 can be operated from a single-phase power supply.

Description of Bulletin 1715-OB8DE

The 1715-OB8DE is a Bulletin 1715 Redundant I/O Module 8-point digital output module.

The module has an 8-point digital output module. It has a maximum power dissipation of 3 watts, supports shielded wire types from 18 to 16 AWG, measures 166 x 42 x 118 mm, and weighs 290 grams.

About the 1715-OB8DE

The 1715-OB8DE, manufactured by Allen-Bradley, is a redundant I/O module that is part of the Allen-Bradley Redundant I/O Module 1715 series.

The 1795-OB8DE has a maximum power dissipation of 3 watts. www.ge-drive.com 1715-OB8DE operates at temperatures as low as -25 degrees Celsius and as high as 70 degrees Celsius.

The redundant l/O module is described as an 8-point digital output module with 18 to 16 AWG wire gauge. the unit has a shipping weight of approximately 290 grams.

The 1715-OB8DE is a chassis-based application with DIN rail mounting.

The 1715-OB8DE has an open housing type with a display system that serves as a dashboard for health and status indication of the module.

The 1715-OB8DE has an output signal of 18 to 32 volts DC.The shipping dimensions of the 1715-OB8DE are 1 5/8 inches long, 4 5/8 inches wide, and 6 1/2 inches high.

According to the manufacturer, the 1715-OB8DE is equipped with 18-16 AWG solid core stranded copper wire rated at less than 2 watts.

The 1715-OB8DE has a vibration resistance of 2 grams and a shock resistance of 25 grams on DIN rail and in operating condition.

The module has a shock resistance of 30 grams in the non-operating condition and when mounted on a DIN rail, and 50 grams when not mounted.

The 1715-OB8DE is available with current source output type and surge transient immunity.

Description of the 1784-PKTXD 2-Channel Communication Card

The 1784-PKTXD 2-channel communication card is manufactured by Allen-Bradley. This communication card uses the PCI bus.

About the 1784-PKTXD

The 1784-PKTXD card is an Allen-Bradley network interface card.

The 1784-PKTXD network interface card is used to connect a PC to a PLC controller via a Data Highway Plus (DH+) or SLC processor and a DH485 network.

This allows the device to enable simpler and more efficient data acquisition processes, which are critical for industrial applications.

The 1784-PKTXD card has an I/O scanner function, which is also available on different cards for use with soft or embedded control engines.

The 1784-PKTXD card includes a generic PCI card as a standard feature. www.ge-drive.com Therefore, the card is compatible with different operating systems.

The 1784-PKTXD card can be used in environments where general programming, configuration, and monitoring functions are required from industrial equipment or computer desktops.

The 1784-PKTXD card is ideally suited for use as a network interface card. Therefore, since it is a general purpose card for interconnecting peripheral components, it must be plugged into a PCI bus slot.

If the operator is using a general purpose card, it must be plugged into a PCI bus slot with either 3.3 volt or 5 volt signals.

The 1784-PKTXD card communicates with nodes on the Data Highway Plus network.

These include the PLC-5. PLC-5/250. and SLC 5/04 processors. This component performs data transfer, management, and local network diagnostics.

The 1784-PKTXD card and the host computer exchange data through a dual-port interface.

The dual-port interface requires up to 4 KB of memory starting at the base memory address that the PCI BIOS addresses for the card when booting the PC.

Description.

The Allen-Bradley 2711-K10G1 Operator Terminal is designed and manufactured as part of the Allen-Bradley/Rockwell Automation Panelview 1000 Series of standard operator terminals.

It has a 10-inch wide screen and supports only greyscale graphics.The 2711-K10G1 Operator Terminal operates on 85 to 264 volts AC at 47 to 63 Hz.

The communication port is a remote I/O communication port.The 2711-K10G1 operator terminal has 256 KB of memory.

About the 2711-K10G1

Allen-Bradley’s 2711-K10G1 is part of the Panelview 1000 series and is designed for users to efficiently connect to machines.

Operators can easily enter information and commands through the keypad. There is a clear 10.1-inch greyscale display.

greyscale display. Each module is housed in a durable NEMA 12/13 or 4X type enclosure and uses 85-264 VAC input power.

A printer (RS-232) port and remote I/O port are available for adaptive communications.

The Allen-Bradley 2711-K10G1 PanelView Standard Operator Interface Terminals are the high standard in control system automation.

They are hard at work around the world supporting the automotive, food and www.ge-drive.com beverage, pulp and paper, water and wastewater treatment, and petrochemical industries.

Each 2711-K10G1 standard terminal is UL, cUL/CSA, and CE listed.

They are rated for NEMA 4X (IP54. IP65) and approved for Class 1 Division 2 (flat panel only) operation.

These terminals are designed and engineered for scalability, reliability and compatibility to reduce cost of ownership and increase productivity.

This 2711-K10G1 device displays critical alarm data and records and displays important data that triggers an alarm.

When an alarm is recognised, the operator is notified to troubleshoot the problem.

The 2711-K10G1 supports up to five languages in a single application, switching between English, French, Italian, German, and Spanish text in run mode without the need for an ATA memory card.

Specifications are as follows

7.2 lbs (3.3 kg)

11 inches (H) x 17 inches (W) x 5 inches (D)

0 to 55°C (32 to 131°F)

Technical Description of the 2711-K10G1

Remote I/O communications and RS-232 printer port.

Product Description.

The Allen-Bradley 6155R-14SXPH computer is a VersaView series compact non-monitor computer.

It is a standard model non-monitor computer with an 80 GB hard drive and 2 GB RAM.

It has Ethernet ports, USB ports, and a mouse or keyboard port.

The 6155R-14SXPH non-display computer has an operating temperature of 0 to www.ge-drive.com 50 degrees Celsius and a storage temperature of -20 to 60 degrees Celsius.

About the 6155R-14SXPH

The Allen-Bradley 6155R-14SXPH is a VersaView 1400R standard non-display C-Series industrial computer with 14 slots.

Specifically, it has 2 half-length ISA slots and 3 PCI slots, as well as 3 full-length ISA slots, 4 PCI slots, and an internal CompactFlash connector.

The computer’s ports include 1 parallel printer port, 2 serial COM ports, and 1 10/100 RJ45 Ethernet port,

1 USB 1.1 port, 1 PS/2 port for keyboard or mouse, and 1 VGA port.

It also has an audio port, a 3.5-inch floppy drive and a CD drive.

It has a 2 GHz Intel Pentium 4 Celeron processor and 256 MB of RAM.

It is expandable up to 2 GB of memory, consisting of two DIMMS with 1 GB of memory. The computer requires an external monitor.

It has an auto range AC input voltage of 90-264V AC, a line frequency of 47-63 Hz, and power consumption of 150V or 1.5 A @ 100V RMS and 0.63 A @ 240V RMS.

Operating temperatures are 0-50 °C and non-operating temperatures are -20-60 °C. The computer can also withstand 15 g of heat. The computer can also withstand operating shocks of 15 g and non-operating shocks of 30 g (both 11 ms ½ sine waves), and 1 Grms of random operating vibration.

and 1 Grms of random operating vibration. The computer’s enclosure is rated NEMA Type 1.

Technical Description of the 6155R-14SXPH

VersaView Non-Display Series Terminal with 2 GB of RAM and 80 GB of hard drive storage with 120-240V AC or 9-36V DC input power.