Category: A-B

The Allen-Bradley 1746-NT8 is an SLC 500 thermocouple/mV analog input module.

The module has eight (8) channels and is compatible with thermocouple sensors such as J, K, T, E, S, R, B, and N. It is also compatible with mV inputs such as +/- 50 mV and +/- 100 mV.

It is also compatible with mV inputs such as +/- 50 mV and +/- 100 mV. The module is compatible with both stationary and modular SLC 500s.

About the 1746-NT8

The 1746-NT8 is Allen-Bradley’s SLC 500 thermocouple/voltage analog input module.

It is a chassis-mounted, eight (8) channel module that receives thermocouple/voltage signals and converts them to digital signals for retrieval by any SLC 500 processor.

It has a backplane current rating of 120mA at 5V DC and 70mA at 24V DC for a total backplane power of 2.28W.

The 1746-NT8 uses a delta-sigma signal conversion method and has a digital low-pass filter with selectable programmable filter frequencies.

The normal mode rejection between terminals is greater than 100 dB at 50-60 Hz, and the common mode rejection between input and ground is greater than 100 dB at 50-60 Hz.

The 1746-NT8 module automatically calibrates itself approximately every 2 minutes after power-up.

It provides +/-30V DC and 600W pulses for 1ms input overvoltage protection and www.ge-drive.com 12.5V DC circuit isolation between inputs and chassis ground, and between inputs and backplane, with a test voltage of 500V DC for 1 minute.

The 1746-NT8 has nine green LEDs to indicate channel status and module status.

It uses the 1746-RT34 (RTB) removable terminal block to connect the input devices. The terminal block includes two (2) cold junction compensation (CJC) sensors with an accuracy of +/-1.72 degrees Celsius.

The 1746-NT8 has several selectable input types with a total input impedance greater than 10 M ohms.

Any input device connected to it must have an impedance of less than 100 ohms to meet accuracy requirements.

The 1746-NT8 offers optional open-circuit detection at 1 cycle per channel for an overall input dry-circuit response time of 400 milliseconds.

The functional temperature range of the module is 0 degrees Celsius to 60 degrees Celsius. The functional temperature range of the module is 0 degrees Celsius to 60 degrees Celsius.

The modules are UL and CUL recognized.

1746-NT8 is an analog input module belonging to the SLC 500 product family.

The module is specifically designed for thermocouple/millivolt inputs and is compatible with SLC 500 processors such as SLC 5/01. 5/02. 5/03. 5/04. and 5/05. It can be used with SLC fixed or modular hardware categories.

Similar to other analog input modules, the 1746-NT8 uses Sigma-Delta modulation to convert received analog signals to digital values.

The converted data is stored in the module’s local memory and transferred to the CPU to create a data table to store the digitally converted values.

The module can be mounted in a fixed chassis, specifically using the 1746-A2 chassis.

If used with a modular controller, the module can be installed in any slot except slot 0.

Slot 0 is always reserved for controllers or communication adapters such as Remote IO, Data Highway Plus (DH+), and Ethernet communication modules.

Available data formats for input signals include engineering units, proportional-integral-derivative (PID) scaling, and proportional counting.

For thermocouple and millivolt input signals, PID proportional is the most compatible data format.

The module is capable of detecting open circuits, under-range, over-range, and channel errors.

These error alarms are assigned specific bits that can be accessed by monitoring systems such as Human Machine Interfaces (HMI) and Supervisory Control and Data Acquisition (SCADA) systems.

DESCRIPTION

The 1783-MX08F Switch is an Allen-Bradley network switch. The module is an 8-port switch with 100 Base-F fiber optic Ethernet ports.

About the 1783-MX08F

The 1783-MX08F Switch, manufactured by Allen-Bradley, is an 8-port Stratix 8000 switch.

The 1783-MX08F switch has a supply voltage of 24 to 48 volts DC and a power dissipation of 10.1 watts.

The Allen-Bradley Stratix 8000 switch has an open enclosure and uses 100 Base-F fiber optic Ethernet ports.

Modules are of the CompactFlash memory type and are rated at 2 amps inrush current.

The 1783-MX08F switch is 112 mm long, 97 mm wide, and 147 mm high.

To ensure optimal performance, it is recommended that users ensure www.ge-drive.com that the ambient operating temperature range is between -40 degrees Celsius and 60 degrees Celsius.

The 1783-MX08F switch has a relative humidity range of 5% to 95% (non-condensing) and a maximum operating vibration of 2 G at 10 to 500 Hz.

It is rated for 20 G of operating shock and 30 G of non-operating shock.

The Allen-Bradley 1783-MX08F switch supports fiber optic Ethernet data rates of 100 Mbps.

The 1783-MX08F switch is optimized for IT and control/manufacturing control environments.

This makes the 1783-MX08F switch a high-performance managed Ethernet switch.

The 1783-MX08F Switch combines Cisco technology with innovative Allen-Bradley/Rockwell Automaton technology for high performance.

The 1783-MX08F switch is easy to set up and enables comprehensive diagnostic information within the specified Allen-Bradley/Rockwell Automation integrated architecture.

The 1783-MX08F switch provides users with the benefits of a CIP interface with predefined Logix tags and advanced configuration screens.

DESCRIPTION

The Allen-Bradley 1771-IR is a PLC5 resistance temperature detector (RTD) input module.

The module has six (6) input channels and is compatible with copper and platinum RTD types.

It is designed to support temperature measurements in Celsius and Fahrenheit units of measurement. It has a scan time of 50 milliseconds for six channels.

About the 1771-IR

The Allen-Bradley 1771-IR is a PLC-5 RTD input with a natural binary BDC supported data format for actual temperature and ohmic readings.

The unit does not require any type of external power supply. It consists of six three-wire RTD inputs.

The device’s channel update resolution www.ge-drive.com introduces a combination of 50ms/6 channels and 16 bits + sign (1.0 degrees Celsius/1.0 degrees Fahrenheit/bit).

The 1771-IR input module has a voltage range of 100 ohms platinum and 10 ohms other. It has a backplane current range of 800mA.

The DC signal delay is 10ms in the on state, 50ms in the off state, and 45(+/- 15) ms in the AC signal delay in the on state.

These input modules have a lifetime of up to 100 million cycles as they meet voltage requirements of 10-276V AC.

The 1771-IR also helps protect your system by providing appropriate troubleshooting assistance. Module indicators show the status of smart inputs or outputs to help you troubleshoot your equipment.

The 1771-IR has an intelligent hybrid interface for connecting on/off devices such as switches, motor starters, pushbuttons, indicators and signalers.

This unique feature helps save on system engineering and spare parts as well as inventory and training costs.

The front panel of each AC discrete input/output module consists of bright status indicators.

The 1771-IR supports both Celsius and Fahrenheit measurement units. The platinum sensor has a temperature measurement range of -200 to +870 degrees Celsius and the copper sensor has a temperature measurement range of -200 to +260 degrees Celsius.

It has a resistance range of 1.00 to 600.00 ohms and a resolution of 0.1 degrees Celsius or 0.1 degrees Fahrenheit when used with a platinum sensor and 0.3 degrees Celsius or 0.5 degrees Fahrenheit.

The 1771-IR draws 950 mA at 5VDC from the backplane, consumes 4.75 watts, and has a thermal dissipation of 16.2 BTU/hour.

It is capable of open wire detection.

The 1771-IR is compatible with PLC2. PLC3. and PLC5 controllers. It can also be installed in various enclosures such as the 1771-A1B, 1771-A2B, 1771-A3B, and 1771-A4B I/O enclosures.

The module uses the 1771-WF pendulum arm to terminate signal lines keyed between 10 and 12 or 28 and 30.

1771-IR Frequently Asked Questions

What are the compatible RTD sensors used with the 1771-IR?

The 1771-IR is compatible with the Platinum 100 and Copper 10 sensors.

How many input channels does the 1771-IR have?

The 1771-IR has six (6) input channels.

Does the 1771-IR require manual calibration?

No. The 1771-IR has automatic calibration.

Technical Description of the 1771-IR

Allen Bradley PLC 5 RTD inputs, natural binary, BDC actual temperature or ohm reading data format, 800 Miliamperes backplane current, no external power supply required.

Related Product Recommendations:

1769-OF8C Analog Output Module

1C31205G01 Remote Node Base Assembly

1C31206G01 Ovation Media Accessories Base Unit

MMS6120 Dual Channel Bearing Vibration Measurement Module

CE3008 Digital Output Module

1C31194G03 Valve Positioner Module

1C31197G05 Valve Positioner Controller Module

350040M 176449-01 Proximity Monitor Module

IC660TBD024K GeniusI/O Terminal Assembly Module

MMS6210 Machinery Health Monitor

Description: Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive component.

The Allen-Bradley 2094-BM01-M is a Kinetix 6000 Drive assembly.

It is a 400VAC rated shaft module with a continuous current of 6.1 A and a peak current of 15.3 A. It has a 98% efficiency and a symmetrical 200.000 A (rms) short circuit current rating.

It has 98% efficiency and a symmetrical short circuit current rating of 200.000 A (rms).

About the 2094-BM01-M

The 2904-BM01-M is an Allen-Bradley component designed for use with Kinetix 6000 drives.

The drive is used as an axis module (AM), is in the 400 VAC voltage category, and has a continuous current of 6.1 A and a peak current of 15.3 A. The drive is designed for use with Kinetix 6000 inverters.

The 2904-BM01-M mounts directly to the Kinetix drive power rail. It is typically mounted next to the Integrated Axis Module (IAM) along the power rails, where the module draws power from the power rails to power its internal circuitry.

The axis module connects to the motor and motion device via feedback cables, auxiliary feedback cables, I/O, and safety wiring.

Axis modules also allow the installation of a control module so that control inputs can be integrated into the module.

The 2904-BM01-M features a 500 Hz bandwidth speed loop and 1300 Hz current loop frequency and a 4 kHz pulse width modulation (PWM) frequency.

The module has a built-in internal shunt with 50 W continuous power, 5.6 kW peak power, and an internal closure resistor rated at 115 Ohms.

The voltage rating is 805VDC with the shunt on and 765VDC with the shunt off.

The efficiency of the module is 98% with a capacitance of 150 ?F and capacitive energy adsorption of 19 joules.

The rated power output of the module is 57 watts (20%), 75% (40%), 90% (60%), 108 watts (8%) and 126 watts (100% load).

These power output data can be used for computer cabinet ventilation purposes.

With its modular design and embedded safety features, the 2094-BM01-M inverter is easy to maintain and offers greater flexibility.

It also simplifies wiring, reduces inventory, and can be modified using advanced technology.

It reduces energy and production waste and improves operational efficiency through its Safe Speed feature.

Its embedded advanced safety features also help protect personnel. Other safety features include safe maximum speed, safe maximum acceleration monitoring,

Safe Direction Monitoring, Zero Speed Monitoring, Enable Switch Control, and Door Monitoring and Control.

The 2094-BM01-Mhas enhanced diagnostic features that indicate the nature of a fault by displaying an error message.

2094-BM01-M Frequently Asked Questions

What is the rated output power range of the 2904-BM01-M?

The rated output power range for the 2904-BM01-M is 57 watts at 20%, 75 watts at 40%, 90 watts at 60%, 108 watts at 8% and 126 watts at 100% load.

Does this shaft module come with an internal shunt and internal shunt resistor?

Yes, the 2904-BM01-M has an internal shunt resistor installed.

Does this module support Safe Torque Off?

No, the module does not. Modules with catalog numbers ending in “S” are the ones that support the Safe Torque Off function.

Technical Description of the 2094-BM01-M

The Allen-Bradley 2094-BM01-M Kinetix 6200 drive has a 460 volt (AC) rating, 3.9 kW watts, and 9 amps output current.

Related Product Recommendations:

IC200ALG327H 12-Channel 13-Bit www.ge-drive.com Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

5X00419G01 Ethernet Link controller

D1961SH45T Rectifier Diode Industrial Robot Accessories

1900-65A-01-00-01-00-00 General Purpose Device Monitor

Description

The Allen-Bradley 1747-SDN is an SLC 500 DeviceNet scanner module.

The module communicates with DeviceNet adapter modules connected to a DeviceNet network.

It is compatible with SLC 5/02 or later controllers. It is a single-slot module that supports operation in slave mode and passes messages in polled, pass-through, state change, cyclic I/O, and pass-through configurations.

It has a backplane current consumption of 5V DC, 500 mA.

About the 1747-SDN

The Allen-Bradley 1747-SDN is a DeviceNet communications scanner.

This scanner module is used to communicate with DeviceNet-enabled devices over a DeviceNet network or through a DeviceNet adapter module.

The module can operate in slave mode; send and receive messages in polled, select-through, state change, and cyclic I/O configurations.

It also supports a pass-through configuration where the 1747-SDN acts as a bridge and www.ge-drive.com connects to a separate DeviceNet network.

This pass-through feature is intended to replace the 1770-KFD, 1784-PCD, 1784-PCID, or 1784-PCIDS DeviceNet connections on the network.

Specifically, the compatible SLC 500 processors when implementing the pass-through configuration are the SLC 5/03. SLC 5/04. and SLC 5/05.

The 1747-SDN supports configuration of up to 63 nodes at a baud rate of 125 Kbps. It draws 5V DC, 500 mA of backplane current.

The 1747-SDN has two (2) LED status indicators mounted on the front panel, such as the Module Indicator to report module operation and a Network Status LED to indicate the DeviceNet communication link.

It also has an LCD display that provides module address and error indications.The DeviceNet terminal is mounted behind the access door and is equipped with a 10-pin plug that plugs into the DeviceNet port.

It serves as an interface between the SLC processor and DeviceNet devices, allowing communication with the processor via M1/M0 file transfer and discrete I/O. The 1747-SDN is compatible with the SLC processor.

The 1747-SDN exchanges configuration data, device I/O data, and status information with the SLC 500 processor.

It draws 500mA of backplane current at 5 V DC and 90mA at 24 V DC.

It consumes 500mA of backplane current at 5 V DC, 90mA at 24 V DC, and provides 30 V circuit isolation from DeviceNet to the backplane for 60 seconds using a basic insulation type tested at 500 V AC.

The 1747-SDN has an IEC-tested operating temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit), non-condensing humidity of 5 to 95 percent, and storage over a temperature range of -40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit).

It also has an IEC-tested 2G vibration resistance at 10-500Hz and a maximum shock rating of 30G.

It has a CISPR 11 Group 1 Class A emission rating and is designated T5 North American temperature code. It has an open housing and is c-UL-us and CE certified.

The Allen-Bradley 1747-SDN is an SLC 500 DeviceNet scanner module.

This DeviceNet scanner module has 1746 backplane communications and is compatible with the following processors: SLC 5/02. 5/03. 5/04. 5/05.

The 1769-L30ER is a 5370 L3 CompactLogix controller with 1MB of user memory, dual Ethernet communication ports, and a single USB port.

The integrated communication ports support multi-node and point-to-point interfaces. Ethernet is the primary communication port used by this device to perform data exchange with a variety of devices.

This port supports linear, ring, and star topologies. Up to 16 nodes can be connected to this controller.

These nodes can consist of Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA), databases, converters, gateways, controllers, and other devices.

These embedded ports also act as embedded switches, which means that the same network traffic is experienced on the controller’s dual ports.

There are two (2) ways to assign an IP address to a controller. First, use Allen-Bradley’s BOOTP-DHCP utility.

This utility searches for a unique IP address for the device and assigns it the specified IP address.

The 1769-L30ER controller supports the installation of up to eight (8) 1769 Compact I/O modules.

In addition, up to three (3) expansion groups can be www.ge-drive.com installed to further expand and maximize the functionality of the controller.

The controller is equipped with status indicators such as RUN, FORCE, BAT, OK, I/O. These LEDs are visible to the user and provide feedback on the controller’s operation.

1769-L30ER Frequently Asked Questions

Does the 1769-L30ER have a memory card?

Yes, the 1769-L30ER has a 1 GB SD memory card.

What kind of network does the 1769-L30ER use?

The 1769-L30ER uses Ethernet.

How many virtual axes can the 1769-L30ER support?

The 1769-L30ER can support 100 virtual axes.

Is the memory of the 1769-L30ER expandable?

Yes, the memory of the 1769-L30ER can be expanded up to 2 GB.

How many local expansion modules can the 1769-L30ER support?

The 1769-L30ER can support up to 8 local expansion modules.

Does the 1769-L30ER have any certifications?

Yes, the 1769-L30ER is cULH certified.

Technical Description of the 1769-L30ER

Allen-Bradley CompactLogix Dual Ethernet Controller device, DLR-enabled, with 1 MB memory capacity, 8 I/O extensions, 16 Ethernet channels.

The controller ships with a 1GB SD card and supports up to a 2GB SD card and CPU module.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

IC660TBD025 GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

1B30035H01 Process Control Base

1769-OF8C Analog Output Module

1769-PB4 Power Supply Module

BSFC-01C Charge control board SP kit gate driver board

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

D1961SH45T Rectifier Diode Industrial Robot Accessories

DESCRIPTION

The 825-MCM20 is a currency converter module from Allen-Bradley.

It is part of the 825-P Motor Modular Protection System and is rated for 690 VAC (IEC) and 600 VAC (CSA/UL).

It has an inrush rating of 6 kV, an operating current range of 2.5-20 amps, a continuous thermal current of 24 amps,

a saturation current rating of 240 amps, and a frequency rating of 50/60 Hz ± 3 Hz.

The converter has a PTC thermistor input and supports six (6) sensors in series.

About the 825-MCM20

The 825-MCM20 is Allen-Bradley’s currency converter module. It is part of the Bulletin 825-P Motor Protection System.

The device is designed primarily to protect industrial three-phase motors, providing thermal overload,

PTC (positive temperature coefficient) overheat, undercurrent (load loss), current unbalance, and phase loss,

overcurrent (load jamming), short circuit, ground fault (residual), ground fault (zero sequence),

frequency and other protective functions, as well as motor start/run and other motor start and run www.ge-drive.com protection functions, such as a variety of motor start and run protection.

Protection prohibition at start, start motor timer, notch or pointing device, TCU (thermal capacity utilization) start prohibition, anti-reverse rotation timer, emergency start,

two-speed protection, reduced voltage start (star-delta) and stall switch.

The 825-MCM20 module is specifically designed for use in a variety of line starter applications,

especially low and medium voltage with 2 or 3 potential transformers, with or without phase current transformers,

with or without zero sequence core balancing current transformers, with or without external RTD module, reversing starters, star delta starters and two speed motors.

The 825-MCM20 operates in accordance with IEC and CSA/UL standards, specifically 690 VAC (IEC) and 600 VAC (CSA/UL), and is rated for 6 kV impact strength.

It has an operating current range of 2.5-20 amps with a continuous thermal current of 24 amps and a saturation current of 240 amps.

The module’s operating frequency range is 50/60 Hz ± 3 Hz. The module provides five (5) discrete inputs; one (1) C-type input; and one (1) C-type input.

The module provides five (5) discrete inputs; one (1) Type C, one (1) Type A, and release contact outputs as well as PTC thermistor inputs for up to six (6) PTC sensors in series.

The Allen-Bradley 825-MCM20 825-M is a current converter device for use with the Allen-Bradley 825 Modular Motor Protection System.

It is specifically designed to protect and manage three-phase industrial motors by monitoring motor current, line voltage, and temperature.

The 825-MCM20 has an operating (working) CSA/UL rating of 600V AC, an IEC rating of 690V AC, and a rated frequency range of 50-60 Hz +/- 3 Hz.

The converter has a functional current range of 2.5A to 20A with a continuous thermal current of 24A and a saturation current of 240A.

It has a converter impulse strength rating of 6kV and a frequency range of 50-60 Hz +/- 3Hz.

The 825-MCM20 has a functional temperature limit of -20 to +60 degrees Celsius (-4 to +140 degrees Fahrenheit) and an ambient non-condensing relative humidity level of 5% to 95%.

The non-operating temperature is limited to -40 to +85 degrees Celsius (-40 to +185 degrees Fahrenheit).

It can operate at altitudes up to 2000 meters without derating and comes with an IP65/IP20 rated enclosure.

It has a maximum operating shock tolerance of 3G for 18ms time duration and resists 3G maximum vibration at frequencies from 10 to 150Hz.

The current converter module weighs approximately 570g and has net dimensions of 120mm x 85mm x 102mm.

Technical Description of the 825-MCM20

The Allen-Bradley 825-MCM20 module is a Bulletin 825 converter module designed to protect three-phase industrial motors.

It supports a current range of 2.5 to 20 amps and is rated at 24 amps continuous thermal current.

The 825-MCM20 converter module is designed to be connected to phase current inputs. It supports an operating frequency range of 50 to 60 Hz.

The 825-MCM20 converter module is protected by an environmentally friendly enclosure rated up to IP 66.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

IC200ALG260 Analog Input Module Analog Input Module

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

5X00419G01 Ethernet Link controller

D1961SH45T Rectifier Diode Industrial Robot Accessories

1900-65A-01-00-01-00-00 General Purpose Device Monitor

DESCRIPTION: The Allen-Bradley 825-P is a motor relay used as a protective device for three-phase motors.

It has standard protection features such as thermal overload (thermal model, PTC (positive temperature coefficient), overheat, undercurrent (load loss),

current unbalance and phase loss, overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency. This unit requires 110-240VAC power input.

About the 825-P

The 825-P is a protective relay for use with three-phase motors. Manufactured by Allen-Bradley, the device is

It provides standard protections such as thermal overload (thermal modeling), PTC (positive temperature coefficient), overheat, undercurrent (load loss), current imbalance, and phase loss.

overcurrent (load seizure), short circuit, ground fault (residual), ground fault (zero sequence), motor start/run and frequency.

For motor start/run protection, this motor relay is capable of starting the motor timer via a protection disable during startup, a startup

notch or pointing device, TCU (Thermal Capacity Utilization) start inhibit, anti-reverse spin timer, emergency start, two-speed protection, reduced voltage start (star-delta), and stall switching to protect the motor.

It can be fitted with RTD-based protection via the 825-PR12D RTD RTD scanner, where up to twelve (12) RTDs can be connected and monitored.

The 825-P is also capable of monitoring event summaries that include information such as relay ID, date and time, trip triggers, and current and voltage amplitudes.

It can also monitor the Serialized Event Record (SER) and motor runtime and history of the last reset and start cycle since the last reset.

Emergency start cycles since the last reset can also be monitored by the unit, which also incorporates a full suite of metering functions.

The 825-P can optionally be fitted with an I/O channel consisting of one (1) 4-20 mA analog output, three (3) control inputs and four (4) contact outputs.

Additional communication interfaces can be installed, including adapters for DeviceNet and Modbus protocols.

The 825-P’s relay outputs also have a 4kV surge strength with a pickup time of < 10ms and provide an insulation voltage rating of 300V AC.

The system has 120V AC/DC (825-PIOD) inputs, a steady state current of 15mA at 2mA and 0.2mA on/off state currents, and on-state and off-state voltages of 15V and 5V respectively.

The system features thermal overload protection and optional voltage-based protection (overvoltage, reactive power, phase inversion, and undervoltage).

The 825-P has a modular construction with a built-in fixed keypad on the front panel and an LCD status display with LED status indicators.

It uses DeviceNet communication options at 125. 250. or 500kbps over distances of 500m, 200m, or 100m and is enclosed in a NEMA 4 (IP65) rated enclosure.

It has an operating temperature of -4 to +140 degrees Fahrenheit, a non-condensing relative humidity of 5% to 95%, and a storage temperature of -40 to +185 degrees Fahrenheit.

It weighs approximately 6.46 kilograms (including power supply and converter modules) and is CE, UL, and CSA listed.

825-P Frequently Asked Questions

What is the proper installation method for the 825-P motor relay?

The modular protective relay 825-P mounts flush to the enclosure.

What are the power requirements for the 825-P?

The Allen-Bradley 825-P is powered from an external supply voltage range of 110-240VAC.

What is the energy metering capability of the 825-P motor relay?

The 825-P motor relay energy metering capabilities include MWh and MVARh parameters.

Technical Description of the 825-P

Allen-Bradley 825-P Modular Protection System with 110-240V AC and DeviceNet Communication

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

IC200ALG260 Analog Input Module Analog Input Module

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

5X00419G01 Ethernet Link controller

D1961SH45T Rectifier Diode Industrial Robot Accessories

1900-65A-01-00-01-00-00 General Purpose Device Monitor

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly

Descripción

The 2093-AC05-MP1 drive is an Allen-Bradley/Rockwell Automation Kinetix 2000 Series multi-axis servo drive.

It is also an Integrated Axis Module type servo drive. 2093-AC05-MP1 Multi-Axis Servo Drives require clearance on the top and bottom for air-cooling, but not on the left or right sides.

This servo drive can be used with compatible SERCOS fiber optic cables.The 2093-AC05-MP1 Multi-Axis Servo Drive has a three-phase mains input voltage range of 170 to 264 volts AC.

About the 2093-AC05-MP1

The Kinetix 2000 Multi-Axis Servo Drives have output power requirements between 3 – 45 kW (4 – 49 amps) and are designed to provide Kinetix integrated motion solutions for applications.

Kinetix 2000 multi-axis servo drives are available in several series, including the 2093-AC05-MPx, 2093-AM0x, 2093-AMPx, 2093-ASP06.

2093-PRSxx, 2093-PRF, 2094-AL09. 2094-AL15S, 2094-AL25S, 2094-AL50S,

2094-AL75S, and 2094-AL75S-C2. 2093-AC05-MPx is a family of Kinetix 2000 multi-axis servo drives.

It includes the 2093-AC05-MP1. 2093-AC05-MP2. and 2093-AC05-MP5.The 2093-AC05-MP1 consists of one specific assembly.

The 2093-AC05-MP1 consists of a specific assembly that includes the Integrated Axis Module (IAM) www.ge-drive.com mounted on the power rails and is a 230 VAC power converter and inverter.

The power rails (PR) consist of copper bus bars and circuit boards with connectors for each module.

The power rail provides power and control signals from the inverter section to the adjacent inverter, which also consists of compatible servo motors (low inertia, food grade, and stainless steel) and compatible linear actuators.

Includes MPAI-Axxx (integrated actuator) 230-volt actuator. 2093-AC05-MP1 specifications include specifications for the power converter, the

Input voltage, 264 V RMS AC, Input frequency, 47 Hz AC, Input voltage, 240 V DC (common bus follower), Input current, 240 V DC (common bus follower), Input current, 240 V DC (common bus follower).

DC (common bus follower) is 6.42 amps Three-phase power input, bus output voltage, nominal 325 V DC, continuous power output to bus is 3.0 KW, the

Peak power output is 6.0 KW with 95% efficiency and 540 NF converter capacitance. 2093-AC05-MP1 is equipped with an IAM inverter power supply.

The bandwidth vel. loop is 500 Hz, similar to most of the 2093 IAM series, with a nominal input voltage of 325 volts dc.

The continuous current (RMS) is 1.0 amps, which is quite different from the MP2 and the MP3 in this series.

Peak current (RMS is 3.0 amps, and peak output current time, up to 3 seconds from 0% drive utilization (0% soak).

It has 98% efficiency, 200 NF capacitance, and 7.5 J capacitive energy absorption.

The 2093-AC05-MP1 is the same as the other MPs in the series, including the 2093-AC05-MP2 and 2093-AC05-MP5.

Equipped with a unique shunt module (2093-ASP06), the 2093-AC05-MP1 has an auxiliary control power of 0.30 amps, unlike the others in the series.

The 2093-AC05-MP1’s main and control power inputs are 264 volts AC three-phase, and it is also equipped with a DC common bus fuse with a contactor rated for 264 volts AC three-phase.

The transformer specifications for the control power input have 500 VA input voltage amperage, 230 V AC input voltage, and 240 V AC output voltage.

The power consumption specifications for the 2093-AC05-MP1 power converter as a percentage of rated power output (watts) are 20% (7.0), 40% (10.5), 60% (14.0), 80% (17.4), and 100% (20.9).

2093-AC05-MP1 Power inverter power consumption as a percentage of rated power output (watts) is 20% (31.6), 40% (33.6), 60% (35.6), 80% (37.6) and 100% (39.6).

The 2093-AC05-MP1 also has an ambient S feature with operating (0 to 50 °C (32 to 22 °F)) and non-operating (-40 to 85 °C (-40 to 85 °F)) modes for ambient temperature, and operating (5 to 95%) and non-operating modes for ambient temperature.

and relative humidity in operating (5 to 95% non-condensing) and non-operating (5 to 95% non-condensing) modes.

It vibrates at 5….. .55 Hz @ 0.35 mm (0.014 in.) double amplitude, continuous displacement; 55 to 500 Hz.

Peak constant acceleration of 2.0 g, shock of 15 g, 11 ms half-sine pulses (3 pulses in each of 3 mutually perpendicular directions) and B31: DSP and SERCOS pins.

Dust and moisture resistant 1B73LSE: Power rail connector pins, converter, inverter, splitter, power rail and slot filler PCB assemblies, UL creepage clearance, clearance issues and conformal coating.

It also features a 1.32 kg (2.9 lb) weight and a 4 mm2 (10 AWG) recommended wire size line filter (2090-XXLF-TC316 (Tesch NF310-16)).

Technical Description for 2093-AC05-MP1

2093-AC05-MP1: Allan Bradley 3Kilowatts Integrated Axis Module – 0.3 Kilowatts.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

IC200ALG260 Analog Input Module Analog Input Module

HE697RTM700B High-Speed Counter Module

1769-OF8C Analog Output Module

5X00419G01 Ethernet Link controller

D1961SH45T Rectifier Diode Industrial Robot Accessories

1900-65A-01-00-01-00-00 General Purpose Device Monitor

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fan Cooling Fan Assembly

The 4-LV40R for the Allen-Bradley/Rockwell Automation Dataliner DL2706 Plus Series

The Message Display Terminal can be used to replace older terminals in the DL40. DL20. and DL10 product lines.

It is a 4-line display terminal that can display up to 4 lines of text at a time*.

The 2706-LV4R Message Display Terminal has 128 KB of memory for user applications and www.ge-drive.com 128 KB of flash memory.

Its screen is a vacuum fluorescent display with adjustable brightness.

The 2706-LV4R Message Display Terminal can be installed into the same panel cutout as the DL40. DL20. and DL10 terminals it is designed to replace.

The Allen-Bradley 2706-LV4R is a DL40 Plus message display.

It is a next-generation message display that directly replaces the models in the older Dataliner DL40 / DL20 series.

It has a vacuum fluorescent display (VFD) with adjustable brightness.

It has a four-line configuration with remote I/O and can display up to 20 characters per line*.

It has 128 KB of RAM and a 120 to 240 VAC input power supply.

The 2706-LV4R display supports bi-directional communication with PLCs and SLCs.

For communication, it has an RS-484 port for file transfer and an RS-232 port for uploading and downloading files.

It displays a variety of symbols and characters and can be read from up to 25 feet away*.

Applications developed for the previous DL40/DL20 series are compatible with the DL40 Plus.

It has various features such as embedded variables, message chaining, hidden messages, and data mode selection.

It supports real-time clock and RS-232 message triggering. It provides recovery in case of power failure during message editing.

It has isolated I/O ports and replaceable batteries and supports enhanced point-to-point communication from the message display.

Other enhancements include red, green, or amber message display colors and remote display relay control.

The 2706-LV4R message displays are highly customizable to effectively communicate alarms and messages in industrial environments.

DL40P Series Message Display with 4-line, 20-character VFD and 120 or 240V AC input power and 128K RAM memory.