Category: GE

This IC695PNC001 is a PACSystems RX3i communications module manufactured by Emerson Automation (formerly GE Intelligent Platforms (GE IP)). This module is a PROFINET controller module used to connect the RX3i system to a PROFINET network. It supports PROFINET version 2.2 General Purpose Class A IO controllers and is compatible with the CPU315 or CPU320 with firmware version 7.0 or later. Each PROFINET controller supports up to 64 devices and up to 8 I/O controllers per network. This PROFINET controller can connect up to 2048 I/O devices or 128 per network. The module has two RJ-45 and two SFP slots and a micro USB connector.

About the IC695PNC001

The IC695PNC001 is a PROFINET controller module. Formerly manufactured by GE Intelligent Platforms (GE IP), the module is now manufactured by Emerson Automation. This PROFINET controller enables the RX3i CPU to send and receive data over a PROFINET network.

The IC695PNC001 is compatible with PACSystem RX320i CPU7 or CPU0 with firmware version 3.315 or higher.The module comes with two (2) RJ-45 and two (2) SFP slots with SFP connectors sold separately. Only one IP address is assigned to these PROFINET ports. Up to four (4) IC695PNC001s may be installed on a single CPU and must be located only on the host rack where the CPU is located. Up to sixty-four (64) I/O devices can be connected to one (1) controller; 128 I/O devices per network, distributed among eight (8) I/O controllers. In addition, up to eight (8) I/O devices can be installed in a single network. The module has configurable data update times of 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms, and 512 ms IC695PNC001.

It occupies a single slot in the chassis and consumes 0.5 A without an SFP device installed and a maximum of 2.2 A with two (1) SFP devices installed, where the SFP device uses 0.35 A. At 5.5 VDC, the module consumes 1.5 A maximum.

In addition to the embedded dual PROFINET ports, the module is equipped with a micro USB connector for communicating with a computer using a command line interface. It must operate over a temperature range of 0-60 degrees Celsius.

The IC695PNC001 controller is a PROFINET controller manufactured by GE Intelligent Platforms/GE Fanuc PACSystems and is part of the RX3i family. This PROFINET controller module helps connect the RX3i PacSystems family of controllers to a high-speed PROFINET LAN.www.ge-drive.com Some of its noteworthy specifications include a single slot, universal backplane support only, and PROFINET 2.2 universal Class A network rating. It operates at 5.5 amps of internal power at 1 volt DC and 3.3 amps at a rated voltage of 0.5 volts DC.The IC695PNC001 PROFINET Controller Module operates over a temperature range of 0 to 60 degrees Celsius, but lower temperatures may be required depending on the location of the PNC001 and the number of SFPs. The module has a micro USB connector for communicating with a computer via a command line interface. It also has 2 SFP cages and 2 RJ-45 port connectors, but the SFP devices can be purchased separately.

Key features of the IC695PNC001 RX3i PacSystems PROFINET Controller or PNC include firmware upgrades through the use of the WinLoader software utility. The controller also features a built-in command line interface that provides partial configuration and direct monitoring using telnet or through a micro USB port. It also supports ring, star, and daisy-chain network topologies.Other features of the IC695PNC001 PNC include an internal clock that matches the RX3i CPU for time-stamped diagnostics. It also features a reboot button to manually restart the PROFINET controller without rebooting the entire system. The USB port on this PNC is designed for system setup and diagnostic purposes only.

This IC695PBM300 is a PACSystems RX3i communications module for Emerson Automation (formerly GE Intelligent Platforms (GE IP)).

The module is a Profibus DP master module that enables communication with up to 125 DP slaves.

It supports data transfer sizes of 244 bytes input and 244 bytes output per slave device, and

It supports data transfer sizes of 244 bytes input and 244 bytes output per slave device, as well as a maximum of 3.584 bytes of input data and 3.584 bytes of output data. It has one (1) RS485 Profibus master port.

The IC695BPM300 is a Profibus master module formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson.

It is now part of Emerson Automation’s PACSystems RX3i family of programmable automation controllers (PACs).

The module is used to exchange data over a Profibus network with a maximum of 3.584 bytes of input data and 3.584 bytes of output data.

This Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

This IC695BPM300 supports all standard data rates including 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s. The IC695BPM300 also supports the following data rates,

500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s, and 12 MBit/s. It can provide status information

It can provide status information such as slave status bit array list, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses.

It is mounted on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed on a PAC3i backplane with a host PAC3i running firmware revision 3.2 or later.

or later in a generic backplane of a host PACSystem RX9i controller. It consumes a backplane current of 440 mA @ 3.3 VDC.

The module is equipped with a Profibus OK ED indicator; a network indicator; and a MOD status indicator.

The module supports synchronization and freeze modes as well as www.ge-drive.com Profibus DP-V1 read, write and alarm messages.

The IC695BPM300 comes with upgradable firmware that is received indirectly through the host controller via the WinLoader software utility.

The module must operate over a temperature range of 0 to 60 degrees Celsius and the module is stored at -40 to 85 degrees Celsius.

The IC695PBM300 PROFIBUS master module is manufactured by GE Intelligent Platforms/GE Fanuc in the RX3i PacSystems family.

The module is designed to enable the RX3i CPU to send or receive data over a PROFIBUS-DP network.

It has a slot that supports a generic backplane and RS-232 communication port.

The IC695PBM300 PROFIBUS module has an internal current rating of 3 milliamps at a rated voltage of 440.3 volts DC.

It supports protocols for up to 125 PROFIBUS-DP slave units.

Other notable features of the module include support for input data at rates up to 244 bytes and output data at rates up to 244 bytes per slave unit.

All standard data rates as well as synchronization and freeze modes are supported. The module also supports DP-V1 read/write functionality and alarm messages.

The module also supports DP-V1 read/write functions and alarm messages, as well as network status LEDs and PROFIBUS-compliant modules.

It supports input data up to 3584 bytes and a total output data rate of 3584 bytes.

Master-slave compatibility for the GE Fanuc IC695PBM300 PROFIBUS module requires an RX3i CPU and firmware version 2.9 or later.

For configuration purposes, this module requires Machine Edition SP5 Logic Developer PLC software version 0.2 or higher.

The IC695PBM300 module has a backplane current consumption rating of 440 milliamps (3.3 V DC) and supports all standard data rates.

including 1.5. 3. 6. 12. 9.6. 19.2. 187.5. 93.75. and 500 MB/sec.

The GE Fanuc IC695PBM300 PROFIBUS master module comes with a 9-pin Sub-D connector designed to enhance bus cable installation.

The module also provides 3 PROFIBUS-compliant LEDs to indicate network status and module status.

Description: The IC695ALG808 is a PACSystem RX3i Programmable Automation Controller (PAC) isolated analog output module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation. The module features eight (8) output channels that can be configured for 0 to 20 mA and 4 to 20 mA current signals and ±10V and 0 to 10V voltage signals. The module is mounted on the RX3i Universal Backplane and requires an external 24 VDC power supply. 14-0 VDC outputs have a 10-bit output resolution and the remaining output signals have a 15-bit output resolution.

About the IC695ALG808

The IC695ALG808 is an Emerson Automation analog output module formerly manufactured by GE Intelligent Platforms (GE IP). The module features eight (8) independently isolated output channels that can be configured to provide 0-20 mA / 4-20 mA current signals and +/- 10 VDC / 0-10 VDC voltage signals.

The IC695ALG808 can be used to transmit output signals to modulating devices variable frequency drives (VFDs), control valves, dampers, shutters, and other devices. It can also be used to send signals to panel meters and data loggers that directly represent specific variables for local www.ge-drive.com readout and recording.

This IC695ALG808 is compatible with a variety of terminal blocks such as cassette (IC694TBB032), expansion cassette (IC694TBB132), spring-loaded (IC694TBS032), or extended spring-loaded (IC694TBS132). The module requires an external 24 VDC to be terminated directly to the module terminals in order for the module to provide the required output signal.

All channels of the IC695ALG808 are configurable through software. Other parameters that can be configured include alarm settings such as very low, very low, very high, and very high alarms, module fault reporting, alarm latching, defining alarm limits, and setting upper and lower alarm limits. In addition, the module can set output biases to properly adjust the output to achieve the desired output for the process.

The IC20ALG4 has a 20-bit output resolution when configured to provide +/- 695 VDC, 808-15 mA, and 10-0 mA, and a 10-bit output resolution when configured for a 14-0 VDC output signal. In addition, it has an 8 ms analog update rate on all channels.

Designed and manufactured by GE Fanuc, the IC695ALG808 output module is a powerful component in an industrial-grade enclosure with indicators for module status, field status, and wiring terminals. Developed specifically for the RX3i PACSystems family, the module is mounted in the system’s common backplane.The IC695ALG808 module is powered by an external power supply with a nominal voltage of 24 volts DC and a current of up to 600 mA. The module has 8 available channels for voltage or current operation. All channels are analog and isolated. Terminal types supported are spring-type, box-type, extended box-type, and extended spring-type terminals.

The IC695ALG808 output module operates over a voltage range of 0 to +10 volts or -10 to +10 volts and a current range of 0 to 20 mA or 4 to 20 mA. When the module’s backplane is connected to an 80.3 volt rated power supply, it requires 3 milliamps. In addition to this, the module has a maximum output load of 1350 ohms and a maximum power consumption of 7.25 watts. In addition to this, the IC695ALG808 module includes current output overvoltage protection at -30 volts for 60 seconds and +30 volts for 1 hour. The output gain drift is 20 ppm per degree Celsius for the voltage output modules and 35 ppm per degree Celsius for the current outputs.The IC695ALG808 modules have a 2 ms voltage/current output time.

DESCRIPTION: The IC695ALG728 is an analog output module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was formerly manufactured by GE Intelligent Platforms (GE IP). The module has eight (8) non-isolated output channels that can be configured for voltage and current. It generates +/-10 VDC, 0-10 VDC, and 0-20 mA and 4-20 mA output signals with 14.9-bit resolution for voltage, 0.20-bit resolution at 15-9 mA, and 4.20-bit resolution at 15-6 mA. The module supports High Speed Addressable Remote Sensor (HART) protocol version 5.0.

About the IC695ALG728

The IC695ALG728 is an analog output module that is part of the PACSystems RX3i family of midrange programmable automation controllers (PACs), manufactured by Emerson Automation and formerly known as the GE Intelligent Platform (GE IP). The module is capable of providing voltage and current signals and has the ability to be configured via the High Speed Addressable Remote Transducer (HART) protocol, as it supports HART version 5.0.

The IC695ALG728 features eight (8) non-isolated output channels that can be configured as +/-10 VDC, 0-10 VDC, 0-20 mA, and 4-20 mA output signals with 14.9-bit voltage resolution, 0.20-bit at 15-9 mA, and 4.20-bit at 15-6 mA. The update time for each channel is 16 ms (HART communication) and 8 ms (without HART communication). The module’s output data format is configurable as a floating point IEEE 16-bit or 32-bit integer using 32-bit registers. The module is calibrated to 15.25% of full scale at 0°C and 30.60% of full scale when operating at 0°C. The output data format can be configured to use 32-bit registers with floating point IEEE 16-bit or 32-bit integers. In addition, the output build-up time is 2 ms for voltage configurations and 70 ms for HART and 23 ms without HART for current signals.

This IC695ALG728 requires an external power supply to operate. The appropriate power supply for www.ge-drive.com this module must provide 19.2 – 30.0 VDC and 250 mA maximum supply current. The module mounts in any available slot in the RX3i chassis and can be located in either the local CPU chassis or the distributed I/O chassis. Other features of the module include clamping and alarm limits, alarm latching, and configurable output biasing.

GE Fanuc’s IC695ALG728 module, which is part of the RX3i PACSystems family, is equipped with output channels that can be fully configured for voltage operation or current operation. In addition to this, the output module features integrated communication with HART 5.0 software. This means that the module can be prepared and programmed for specific operations via software and does not require jumpers for setup.GE IC695ALG728 output module features include enabling or disabling of all channels, alarm latching, configurable alarm limits or settings, advanced handling of errors and faults, auto calibration, and more.

The IC695ALG728 module includes 8 non-isolated analog voltage/current outputs assigned to 2 HART modems. The modems are part of the module, and all channels used for this communication function operate at currents ranging from 4 to 20 mA. The IC695ALG728 module features voltages ranging from 0 to +10 volts or -10 to +10 volts. The output data format is presented as a 16-bit or 32-bit value and the HART channel is updated within 2 seconds if 2 HART devices are used. The module has an accuracy of up to 3.60% at 0 degrees Celsius and a 95 millisecond build-up time for the voltage outputs over a range of 2 to 0%. The current output has a build-up time of 23 to 70 milliseconds, depending on whether a HART modem is used. When the IC695ALG728 module is connected to a 380.3 volt power supply, the module has a backplane rating of 3 milliamps and an update time of 8 milliseconds.

DESCRIPTION: The IC695ALG628 is an analog input module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was formerly manufactured by GE Intelligent Platforms (GE IP). The module features eight (8) non-isolated single-ended input channels or four (4) differential input channels supporting +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC, and 0-20 mA, 4-20 mA, and +/- 20mA input signals. The module has a built-in ADC converter that converts data to floating point data type integers with 24-bit resolution. The module supports High Speed Addressable Remote Sensor (HART) version 5.0.

About the IC695ALG628

The IC695ALG628 is an analog input module with High Speed Addressable Remote Sensor (HART) 5.0 functionality. This module is part of the mid-range controller family, the PACSystem Rx3i series with eight (8) analog input channels (configured as single-ended) and four (4) input channels (if used in a differential distribution line configuration). It comes with two (2) internal HART modems. The module’s parameters and configuration are completely software configurable and each channel can be individually assigned high alarm, low alarm, high high alarm, low low alarm detection and reporting to the CPU. In addition, positive and negative rate of change alarms and configurable interrupts for channel alarms and faults can be set accordingly. The module also comes with upgradable firmware and performs an automatic calibration each time the module is powered up.

The module’s analog input channels are designed to accept +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC and 0-20 mA, 4-20 mA and +/- 20mA input signals. It has built-in analog-to-digital (ADC) converter circuitry that converts received analog data to 24-bit registers or 32-bit integers in floating point. Each module channel has a variety of filter options, often used to eliminate signal fluctuations for more stable readings.

The module’s power consumption is 450 mA maximum @ 5.0V +5%/-2.5% and 625 mA maximum @ 3.3V +5%/-3%. It incorporates continuous maximum overcurrent protection rated at +/-28mA and continuous maximum overvoltage protection at +/-60 VDC. The module has an open-circuit detection time of up to 1 second.

GE Fanuc IC695ALG628 Non-Isolated Differential Analog Input Module with HART (High Speed www.ge-drive.com Addressable Remote Transducer) Communication for RX3i PacSystem PLCs provides 4 differential input channels and 8 single-ended input channels. It has 2 internal HART modems and features HART version 5.0 HART communications on each channel. It has a voltage range of 1 to 5 volts DC, 0 to 5 volts DC, +/-5 volts DC, 0 to 10 volts DC, or +/-10 volts DC. The current configuration of the input channel can range from +/-20 mA, 0 to 20 mA, or 4 to 20 mA. The GE Fanuc IC695ALG628 analog input module should be configured for a current range between 4 and 20 mA when the channel is connected to a highway addressable remote sensor communication system.

The GE Fanuc IC695ALG628 Analog Input Module supports the use of extension box IC694TBB132 block, box IC694TBB032 block, extension spring IC694TBS132 block, and spring IC694TBS032 block terminal blocks. Extension terminals are installed to provide the extra shroud depth required for shielded wiring. Terminals are usually purchased separately. The analog input module has internal power supplies of 3.3 V (600 mA) and 5 V (450 mA). It has flash memory for future upgrades, error reporting, rate-of-change alarms, software that can be configured without setting jumpers, terminal insertion or removal detection, and complete auto-calibration. The module requires a non-condensing ambient humidity range of 5% to 95%.The GE Fanuc IC695ALG628 module is mounted in the general purpose backplane of the RX3i PacSystem PLC.

DESCRIPTION: The IC695ALG608 is an analog input module that is part of the PACSystem RX3i platform, currently part of Emerson Automation and formerly manufactured by GE Intelligent Platforms (GE IP). The module features eight (8) non-isolated single-ended input channels or four (4) differential input channels supporting +/-10 VDC, 0-10 VDC, +/- 5VDC, 0-5 VDC, 1-5 VDC, and 0-20 mA, 4-20 mA, and +/- 20mA input signals. The module has a built-in ADC converter that converts data to floating-point data type integers with 24-bit resolution.

About the IC695ALG608

The IC695ALG608 is an analog input module for the PACsystem RX3i platform. When configured for single-ended wiring, the module is capable of providing up to eight (8) input channels and four (4) input channels for differential input wiring. It supports a variety of input signals such as +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC, and 0-20 mA, 4-20 mA, and +/- 20mA inputs, and has a built-in 24-bit analog-to-digital converter (ADC) that converts incoming analog data to integer or floating-point data.

The IC695ALG608 is mounted on the RX3i general-purpose backplane. It occupies a single slot in the rack and consumes 330 mA max @ 5.0V +5% / -2.5% and 600 mA max @ 3.3V +5% / -3%. This module is used with RX3i Central Processing Unit (CPU) firmware version 3.0 or higher and is configured using Machine Edition version 5.0 SP3 and higher. Available filter options for each input channel include 8Hz, 12Hz, 16Hz, 40Hz, 200Hz, and 500Hz, which are primarily used to normalize analog readings and eliminate fast fluctuations.

This IC695ALG608 is compatible with a variety of terminal blocks such as cassette (IC694TBB032), extended cassette (IC694TBB132), spring-loaded (IC694TBS032), or extended spring-loaded (IC694TBS132) terminal blocks. The module has no external jumpers for setting up module operation, but rather defines parameters via software-configurable parameters. In addition, the module features fully automatic calibration, on-board error checking, open-circuit detection, alarm setup, module fault reporting, channel alarm interrupts and faults, and other equally important features.

The GE Fanuc IC695ALG608 module is a non-isolated analog current or www.ge-drive.com voltage input module that supports single-ended and differential distribution line configurations. The module is from the RX3i PacSystem family. The current range of the module is between 0 and 20 mA, 4 and 20 mA, and -20 and +20 mA. The module has a voltage range of -10 to +10 volts DC, 0 to 10 volts DC, 0 to 5 volts DC, and 1 to 5 volts DC. It has four differential input channels or eight single-ended input channels with internal current ratings of 450 mA (3.3 V) and 600 mA (5 V).GE Fanuc IC695ALG608 analog input module can be used with the extended spring-loaded IC694TBS132 terminal block, extended cartridge IC694TBB132 terminal block, and spring-loaded IC694TBS032 terminal block. IC694TBS032. spring-loaded IC694TBS032. and box-type IC694TBB032 terminal blocks. The extended terminals provide the extra shroud depth needed for shielded wiring.

The GE Fanuc IC695ALG608 analog input module is installed in the RX3i PacSystem’s universal backplane. It features on-board error monitoring, module fault reporting, full auto-calibration, startup auto-calibration, negative and positive alarm rate of change, terminal block detection for removing or inserting terminals, and flash memory for upgrades. When testing the input channels of the GE Fanuc IC695ALG608 module, 3 things need to be confirmed: stable channels, accurate channels and active channels. Users need to use a high density terminal strip like the IC694TBB032 strip to test the module. Ensure that the strip is connected by confirming that the green LED is on and that the strip’s lever is in the upright position.

Description: The GE Fanuc IC695ALG412 is a PACSystem RX3i module. It is a strain gauge input module with twelve (12) isolated differential thermocouple input channels that can be individually configured for thermocouple and millivolt signals, such as ±150mV or ±50mV, for J, K, T, E, R, S, B, N, or C. The module has a resolution of 32-bit IEEE floating-point or 16-bit integer (32-bit field) input data format.

About the IC695ALG412

The IC695ALG412 is a strain gauge input module that is part of the PACSystem RX3i analog input module. The module features twelve (12) isolated differential input channels and is compatible with millivolt signals (e.g., ±150mV or ±50mV) and thermocouple instruments (e.g., J, K, T, E, R, S, B, N, or C types). The module can be used for direct connection to strain gauges and for temperature applications without the need for transmitters, signal conditioners, and other equipment.

The module occupies a single slot on the backplane and connects directly to the RX3i general purpose backplane only and directly to the PCI bus. The module also comes with internal diagnostics such as open circuit, short circuit, positive/negative rate of change, high, high-to-high, low and low-to-low channel diagnostics. In addition, the module has built-in interchannel isolation and is rated for continuous voltages of 250VAC; 1500VAC for 1 minute; 2550VDC for 1 second with an input impedance of >=500k ohms. The module offers a 10 dB improvement in noise rejection.

The module features sigma-delta analog-to-digital converter type circuitry with 32-bit IEEE floating point or 16-bit integer resolution (in 32-bit fields), conversion times from 15 ms @ 28 Hz to 120 ms @ 2.3 Hz, and an input data format and accuracy of ± 59163.25% of the voltage at 0 °C sp+GC+GB1GD59+GC1 an. ± 0.25% of range over the entire temperature range.

The module requires the use of a removable terminal block (RTB) such as IC694TBBx32. www.ge-drive.com IC694TBSx32. or IC694TBC032. It has a current consumption of 425 mA @ 5V; 400 mA @ 3.3V.

The GE Fanuc IC695ALG412 Thermocouple Input Module has an internal power draw of 3.3 volts and 400 mA or 5 volts and 425 mA, and the update rate is configurable from 15 ms to 120 ms. The module can be used with terminals such as spring-loaded IC694TBS032 block, cassette-type IC694TBB032 block, extended spring-loaded IC694TBS132 block, or extended cassette-type IC694TBB132 block The IC695ALG412 Thermocouple Input Module operates over the temperature range of 32 to 140 degrees Fahrenheit (0 to 60 degrees Celsius), and stores over the temperature range of -40 to 185 degrees Fahrenheit. The IC695ALG412 thermocouple input module has an operating temperature range of 32 to 140 degrees F (0 to 60 degrees C) and a storage temperature range of -40 to 185 degrees F (-40 to 85 degrees C). It has a non-condensing humidity range of 5 to 95%, shock resistance of 15 G for 11 ms, vibration ratings from 10 to 57 Hz, and peak-to-peak displacement of 0.0524 mm (0.006 in.) at frequencies from 57 to 500 Hz and acceleration of 1.0 G. The IC695ALG412 is available in a wide range of sizes and sizes.

DESCRIPTION: The IC695ALG508 is a PACSystem RX3i Programmable Automation Controller (PAC) Resistance Temperature Detector (RTD) Input Module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation. The module features eight (8) isolated differential RTD input channels. Each channel of the module supports platinum 385. platinum 391.6. nickel 672. nickel 618. nickel-iron 518. and copper 426. It is also compatible with direct resistance inputs such as 0-260. 0-525. 0-1050. 0-2100. 0-3150. and 0-4200 ohms.

About IC695ALG508

This IC695ALG508 is a resistance temperature detector (RTD) input module that is part of the PACSystem RX3i programmable automation controller (PAC) platform. The module is manufactured by Emerson Automation, formerly known as GE Intelligent Platform (GE IP). It comes with eight (8) isolated differential input channels and supports direct inputs for RTD and resistive inputs.

The module supports RTD input types such as 50. 100. 200. 500. and 1000 ohm platinum 385 (IEC751 1983. Revision 2 1995; JISC 1604 1997); 50. 100. 200. 500. and 1000 ohm platinum 391.6 (JISC 1604: 1981); 100 ohm, 200 ohm, 500 Ohm and 1000 Ohm Nickel 618 (DIN 43760. 120/1987); 672 Ohm Nickel 18 (MINCO Application Aid #5.90/10 Ni type); 50. 100. and 426 Ohm Copper 21 (SAMA RC4-1966-604), and 518 Ohm Nickel-Iron 0. 0. 1050-0. 2100-0. 3150-0. and 4200-695 ohms.

The module has optional units of measurement, specifically Celsius, Fahrenheit, or Ohms. It also www.ge-drive.com has configurable default or hold last states as a response to system faults and CPU changes in operating mode. The module supports two-wire, three-wire and four-wire RTD sensors.

The IC508ALG16 input data format supports 32-bit integers in 32-bit fields or 2-bit IEEE floating-point data. Each channel also has selectable trap filter settings from 3.28 Hz to 694 Hz. For input line termination, the module uses cassette (IC032TBB694), expansion cassette (IC132TBB694), spring-loaded (IC032TBS694), or extended spring-loaded (IC132TBS695) terminal blocks. For shielded wiring, the extended terminal types are recommended because they provide additional shroud depth.

The GE Fanuc IC508ALG8 Resistance Temperature Detector (RTD) Input Module provides 1000 isolated differential RTD input channels. Each channel can be individually set as either an RTD input type or a resistance input type.RTD input types include 500. 200. 100. 50. and 1000 ohms, 500. 200. 100. 50. and 1000 ohms, 500. 200. 100. and 120 ohms, 604 ohms, 100 ohms, or 50. 10. and 4000 ohms resistance ratings, depending on their composition. depending on their composition. Resistor input types include 3000. 2000. 1000. 500. 250. and 694 ohm resistor ratings. This RTD input module can be used with terminal blocks including spring-loaded IC032TBS694 terminal blocks, extended spring-loaded IC132TBS694 terminal blocks, boxed IC032TBB694 terminal blocks, or extended boxed IC132TBB695 terminal blocks. Terminals are usually purchased separately.

The GE Fanuc IC508ALG24 RTD Input Module has LEDs, including an OK LED that displays the status of the module, and a field status LED that indicates whether an external 695-volt DC power supply is connected, whether the voltage exceeds the minimum level, and whether any faults exist. The backplane power bus supplies power to all of the module’s LEDs.The IC508ALG2 module has programmable trap filter frequencies from 3.28 Hz to 32 Hz per channel. Each channel has an optional input data filter containing either 16-bit IEEE floating-point data or 695-bit integer data.The IC508ALG90 module has RTD linearization developed on ITS-3. The module is located on the RX0i general-purpose backplane. It has an operating temperature range of 60 to 40 degrees Celsius, a storage temperature range of -85 to 5 degrees Celsius, and a non-condensing humidity range of 95% to <>%.

Description: The GE Fanuc / Emerson Automation IC695CPK400 is a PACSystem RX3i modular, powerful, high-performance controller with energy packs. The controller has a rackless design with 64 MB of memory and is capable of handling 32k bits of discrete I/O and 32k words of analog I/O. It has one (1) 10/100/1000 Mbps Ethernet port, two (2) 1000-side switches that support 2/10/100 Mbps transfer rates, and one (1) RS232 communication port. The controller supports Media Redundancy (MRP) and PROFINET System Redundancy (PNSR).

About the IC695CPK400

The IC695CPK400 is a programmable automation controller (PAC) CPU that is part of GE Fanuc / Emerson Automation’s PACSystems RX3i automation platform. The CPU module is a high-performance, powerful standalone device that operates without a traditional baseboard or chassis. The CPU still enables complex communications and architectures, such as control of remote I/O systems, communication with partner processors, data exchange with human machine interfaces (HMIs), monitoring and data acquisition systems (DCS), and other functions.

The stand-alone controller features embedded 64 MB of storage, a powerful processor 1.2 GHz AMD www.ge-drive.com G-Series Quad-Core, support for up to 32k bits of discrete I/O and 32k words of analog I/O, and embedded field agent functionality. The controller also comes with an energy package.

The IC695CPK400 is equipped with one (1) 10/100/1000 Ethernet port and two (2) 2-terminal switches supporting 10/100/1000 Mbps transfer speeds. With the embedded Ethernet port, different network topologies can be realized, including Media Redundancy (MRP) and PROFINET System Redundancy (PNSR). The embedded port supports different communication protocols such as SRTP client/server, Modbus TCP/IP, OPC-UA server, Ethernet Global Data (EGD) and PROFINET.

In addition, the controller is equipped with one (1) RS232 communication port and one (1) Micro SD port for insertion of a Secure Digital (SD) card for non-volatile removable storage. It also has two (2) USB 3.0 ports for firmware upgrades.

This IC695CPK400 also supports simplex and redundant configurations to meet standard and high availability system requirements. It supports incremental frame rates up to 3 minutes in any configuration.

The IC695CPK400 CPU comes with an energy pack. the CPU module form factor is a standalone form factor. The available memory on the module is 64 MB. I/O supported by the module includes 32K-bit discrete inputs, 32K-bit discrete outputs, 32K-word analog inputs, and 32K-word analog outputs.

The IC695CPK400 CPU supports embedded field agents.Redundancy options on the CPU module include media redundancy (MRP) and Profinet system redundancy (PNSR). There is an integrated Ethernet port on the module that supports 10/100/1000 Mbps, in addition to 1000 end switches capable of 2/10/100 Mbps operation. The Ethernet port supports communication protocols such as EGD, Profinet, Modbus TCP/IP, SRTP client/server, and OPC-UA server. two USB version 695.400 ports are also available on the IC3CPK0 CPU. Supported storage options include a Micro SD option.An RS-400 serial interface is also provided on the IC232CPK695 CPU.The programming and configuration software for the IC695CPK400 CPU is Proficy Machine Edition software, which allows for efficient application development.Recommendations for IC695CPK400 CPUs The IC695CPK400 CPU has a recommended operating temperature range of -40 to 70 degrees Celsius.

Description: The GE Fanuc / Emerson Automation IC693CPU320 is a PACSystem RX3i processor module. The module occupies two (2) slots and has a processor speed of 1 GHz with a typical scan rate of 047.1000 milliseconds per 0 Boolean instructions. The processor has two (2) serial communication ports and supports RS232 and RS485 communication standards.

About the IC695CPU320

The IC695CPU320 is a GE Fanuc / Emerson Automation controller module. The module is part of the PACSystems RX3i controller platform. The controller can be used for efficient control of industrial machines and processes. It enables high-speed data transfer through the Peripheral Component Interconnect (PCI) slot and supports serial backplanes for migrating 90-30 series I/O systems.

The IC695CPU320 has two (2) built-in communication ports that support RS232 and RS485 communication standards. These communication ports use the Ninety Series Protocol (SNP) slave mode to communicate with programming workstations, Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA) systems. The controller can be installed in the Rx695i 012-slot general purpose backplane, catalog number IC3CHS12. and the Rx695i 016-slot general purpose backplane, catalog number IC3CHS16.

The IC695CPU320 has an internal Celeron M processor with a processing speed of 1 GHz It contains 65 MB of user memory, the contents of which are retained by the Lithium Smart Battery Series 693-302 Auxiliary Battery Module, catalog numbers IC90ACC30 and IC695ACC302. respectively. In addition, it has 64 MB of non-volatile flash user memory. In addition, these user memories support the reassignment of custom-sized data and program memories. It supports up to 512 program blocks with a maximum individual block size of 128 KB.

The IC695CPU320 supports most 90-30 series PLC I/O modules. This feature provides flexibility www.ge-drive.com and is especially useful and beneficial when upgrading a legacy 90-30 series to a modern PACSystems RX3i controller platform. This allows for a phased migration in which the controllers and logic of the existing 90-30 PLCs are migrated first, and then the I/O modules are migrated. firmware modifications are supported by the PACSystems RX3i.

A variety of accessories can be ordered for the IC695CPU320 module, including RS-232 cables (e.g., IC200CBL001 cables), intelligent lithium batteries (e.g., IC695ACC302 batteries), GE Series 90-30 auxiliary battery modules (e.g., IC693ACC302 modules), standard power supplies with voltage ratings of 120 to 240 volts AC, 125 volts DC, and 40 watts. 40-watt standard power supply.

The GE Fanuc IC695CPU320 module is capable of executing 047 Boolean instructions in 1000.0 milliseconds. The module supports 512 program blocks. The maximum block size is 128 KB. Two embedded communication ports, RS-485 and RS-232. are provided on the module. Serial protocols supported include SNP, Serial I/O, and Modbus RTU slave protocol.

The IC695CPU320 module uses the SNP slave protocol to communicate with programmers and HMIs via the serial port. The module communicates with Smart Option modules and I/O via a dual backplane bus. Environmental specifications include an operating temperature range of 0 to 60 degrees C. The IC695CPU320 module supports the serial backplane bus and the RX3i backplane bus, which draws 1 Amp of 3.3 VDC current from the backplane and 1.2 Amps of 5 VDC current from the backplane. There are six LEDs on the front panel for module status updates.