This IC695PBM300 is a PACSystems RX3i communications module for Emerson Automation (formerly GE Intelligent Platforms (GE IP)).

The module is a Profibus DP master module that enables communication with up to 125 DP slaves.

It supports data transfer sizes of 244 bytes input and 244 bytes output per slave device, and

It supports data transfer sizes of 244 bytes input and 244 bytes output per slave device, as well as a maximum of 3.584 bytes of input data and 3.584 bytes of output data. It has one (1) RS485 Profibus master port.

The IC695BPM300 is a Profibus master module formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson.

It is now part of Emerson Automation’s PACSystems RX3i family of programmable automation controllers (PACs).

The module is used to exchange data over a Profibus network with a maximum of 3.584 bytes of input data and 3.584 bytes of output data.

This Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

This IC695BPM300 supports all standard data rates including 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s. The IC695BPM300 also supports the following data rates,

500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s, and 12 MBit/s. It can provide status information

It can provide status information such as slave status bit array list, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses.

It is mounted on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed on a PAC3i backplane with a host PAC3i running firmware revision 3.2 or later.

or later in a generic backplane of a host PACSystem RX9i controller. It consumes a backplane current of 440 mA @ 3.3 VDC.

The module is equipped with a Profibus OK ED indicator; a network indicator; and a MOD status indicator.

The module supports synchronization and freeze modes as well as www.ge-drive.com Profibus DP-V1 read, write and alarm messages.

The IC695BPM300 comes with upgradable firmware that is received indirectly through the host controller via the WinLoader software utility.

The module must operate over a temperature range of 0 to 60 degrees Celsius and the module is stored at -40 to 85 degrees Celsius.

The IC695PBM300 PROFIBUS master module is manufactured by GE Intelligent Platforms/GE Fanuc in the RX3i PacSystems family.

The module is designed to enable the RX3i CPU to send or receive data over a PROFIBUS-DP network.

It has a slot that supports a generic backplane and RS-232 communication port.

The IC695PBM300 PROFIBUS module has an internal current rating of 3 milliamps at a rated voltage of 440.3 volts DC.

It supports protocols for up to 125 PROFIBUS-DP slave units.

Other notable features of the module include support for input data at rates up to 244 bytes and output data at rates up to 244 bytes per slave unit.

All standard data rates as well as synchronization and freeze modes are supported. The module also supports DP-V1 read/write functionality and alarm messages.

The module also supports DP-V1 read/write functions and alarm messages, as well as network status LEDs and PROFIBUS-compliant modules.

It supports input data up to 3584 bytes and a total output data rate of 3584 bytes.

Master-slave compatibility for the GE Fanuc IC695PBM300 PROFIBUS module requires an RX3i CPU and firmware version 2.9 or later.

For configuration purposes, this module requires Machine Edition SP5 Logic Developer PLC software version 0.2 or higher.

The IC695PBM300 module has a backplane current consumption rating of 440 milliamps (3.3 V DC) and supports all standard data rates.

including 1.5. 3. 6. 12. 9.6. 19.2. 187.5. 93.75. and 500 MB/sec.

The GE Fanuc IC695PBM300 PROFIBUS master module comes with a 9-pin Sub-D connector designed to enhance bus cable installation.

The module also provides 3 PROFIBUS-compliant LEDs to indicate network status and module status.