News

Description: The GE Fanuc IC695ALG412 is a PACSystem RX3i module. It is a strain gauge input module with twelve (12) isolated differential thermocouple input channels that can be individually configured for thermocouple and millivolt signals, such as ±150mV or ±50mV, for J, K, T, E, R, S, B, N, or C. The module has a resolution of 32-bit IEEE floating-point or 16-bit integer (32-bit field) input data format.

About the IC695ALG412

The IC695ALG412 is a strain gauge input module that is part of the PACSystem RX3i analog input module. The module features twelve (12) isolated differential input channels and is compatible with millivolt signals (e.g., ±150mV or ±50mV) and thermocouple instruments (e.g., J, K, T, E, R, S, B, N, or C types). The module can be used for direct connection to strain gauges and for temperature applications without the need for transmitters, signal conditioners, and other equipment.

The module occupies a single slot on the backplane and connects directly to the RX3i general purpose backplane only and directly to the PCI bus. The module also comes with internal diagnostics such as open circuit, short circuit, positive/negative rate of change, high, high-to-high, low and low-to-low channel diagnostics. In addition, the module has built-in interchannel isolation and is rated for continuous voltages of 250VAC; 1500VAC for 1 minute; 2550VDC for 1 second with an input impedance of >=500k ohms. The module offers a 10 dB improvement in noise rejection.

The module features sigma-delta analog-to-digital converter type circuitry with 32-bit IEEE floating point or 16-bit integer resolution (in 32-bit fields), conversion times from 15 ms @ 28 Hz to 120 ms @ 2.3 Hz, and an input data format and accuracy of ± 59163.25% of the voltage at 0 °C sp+GC+GB1GD59+GC1 an. ± 0.25% of range over the entire temperature range.

The module requires the use of a removable terminal block (RTB) such as IC694TBBx32. www.ge-drive.com IC694TBSx32. or IC694TBC032. It has a current consumption of 425 mA @ 5V; 400 mA @ 3.3V.

The GE Fanuc IC695ALG412 Thermocouple Input Module has an internal power draw of 3.3 volts and 400 mA or 5 volts and 425 mA, and the update rate is configurable from 15 ms to 120 ms. The module can be used with terminals such as spring-loaded IC694TBS032 block, cassette-type IC694TBB032 block, extended spring-loaded IC694TBS132 block, or extended cassette-type IC694TBB132 block The IC695ALG412 Thermocouple Input Module operates over the temperature range of 32 to 140 degrees Fahrenheit (0 to 60 degrees Celsius), and stores over the temperature range of -40 to 185 degrees Fahrenheit. The IC695ALG412 thermocouple input module has an operating temperature range of 32 to 140 degrees F (0 to 60 degrees C) and a storage temperature range of -40 to 185 degrees F (-40 to 85 degrees C). It has a non-condensing humidity range of 5 to 95%, shock resistance of 15 G for 11 ms, vibration ratings from 10 to 57 Hz, and peak-to-peak displacement of 0.0524 mm (0.006 in.) at frequencies from 57 to 500 Hz and acceleration of 1.0 G. The IC695ALG412 is available in a wide range of sizes and sizes.

DESCRIPTION: The IC695ALG508 is a PACSystem RX3i Programmable Automation Controller (PAC) Resistance Temperature Detector (RTD) Input Module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation. The module features eight (8) isolated differential RTD input channels. Each channel of the module supports platinum 385. platinum 391.6. nickel 672. nickel 618. nickel-iron 518. and copper 426. It is also compatible with direct resistance inputs such as 0-260. 0-525. 0-1050. 0-2100. 0-3150. and 0-4200 ohms.

About IC695ALG508

This IC695ALG508 is a resistance temperature detector (RTD) input module that is part of the PACSystem RX3i programmable automation controller (PAC) platform. The module is manufactured by Emerson Automation, formerly known as GE Intelligent Platform (GE IP). It comes with eight (8) isolated differential input channels and supports direct inputs for RTD and resistive inputs.

The module supports RTD input types such as 50. 100. 200. 500. and 1000 ohm platinum 385 (IEC751 1983. Revision 2 1995; JISC 1604 1997); 50. 100. 200. 500. and 1000 ohm platinum 391.6 (JISC 1604: 1981); 100 ohm, 200 ohm, 500 Ohm and 1000 Ohm Nickel 618 (DIN 43760. 120/1987); 672 Ohm Nickel 18 (MINCO Application Aid #5.90/10 Ni type); 50. 100. and 426 Ohm Copper 21 (SAMA RC4-1966-604), and 518 Ohm Nickel-Iron 0. 0. 1050-0. 2100-0. 3150-0. and 4200-695 ohms.

The module has optional units of measurement, specifically Celsius, Fahrenheit, or Ohms. It also www.ge-drive.com has configurable default or hold last states as a response to system faults and CPU changes in operating mode. The module supports two-wire, three-wire and four-wire RTD sensors.

The IC508ALG16 input data format supports 32-bit integers in 32-bit fields or 2-bit IEEE floating-point data. Each channel also has selectable trap filter settings from 3.28 Hz to 694 Hz. For input line termination, the module uses cassette (IC032TBB694), expansion cassette (IC132TBB694), spring-loaded (IC032TBS694), or extended spring-loaded (IC132TBS695) terminal blocks. For shielded wiring, the extended terminal types are recommended because they provide additional shroud depth.

The GE Fanuc IC508ALG8 Resistance Temperature Detector (RTD) Input Module provides 1000 isolated differential RTD input channels. Each channel can be individually set as either an RTD input type or a resistance input type.RTD input types include 500. 200. 100. 50. and 1000 ohms, 500. 200. 100. 50. and 1000 ohms, 500. 200. 100. and 120 ohms, 604 ohms, 100 ohms, or 50. 10. and 4000 ohms resistance ratings, depending on their composition. depending on their composition. Resistor input types include 3000. 2000. 1000. 500. 250. and 694 ohm resistor ratings. This RTD input module can be used with terminal blocks including spring-loaded IC032TBS694 terminal blocks, extended spring-loaded IC132TBS694 terminal blocks, boxed IC032TBB694 terminal blocks, or extended boxed IC132TBB695 terminal blocks. Terminals are usually purchased separately.

The GE Fanuc IC508ALG24 RTD Input Module has LEDs, including an OK LED that displays the status of the module, and a field status LED that indicates whether an external 695-volt DC power supply is connected, whether the voltage exceeds the minimum level, and whether any faults exist. The backplane power bus supplies power to all of the module’s LEDs.The IC508ALG2 module has programmable trap filter frequencies from 3.28 Hz to 32 Hz per channel. Each channel has an optional input data filter containing either 16-bit IEEE floating-point data or 695-bit integer data.The IC508ALG90 module has RTD linearization developed on ITS-3. The module is located on the RX0i general-purpose backplane. It has an operating temperature range of 60 to 40 degrees Celsius, a storage temperature range of -85 to 5 degrees Celsius, and a non-condensing humidity range of 95% to <>%.

Description: The GE Fanuc / Emerson Automation IC695CPK400 is a PACSystem RX3i modular, powerful, high-performance controller with energy packs. The controller has a rackless design with 64 MB of memory and is capable of handling 32k bits of discrete I/O and 32k words of analog I/O. It has one (1) 10/100/1000 Mbps Ethernet port, two (2) 1000-side switches that support 2/10/100 Mbps transfer rates, and one (1) RS232 communication port. The controller supports Media Redundancy (MRP) and PROFINET System Redundancy (PNSR).

About the IC695CPK400

The IC695CPK400 is a programmable automation controller (PAC) CPU that is part of GE Fanuc / Emerson Automation’s PACSystems RX3i automation platform. The CPU module is a high-performance, powerful standalone device that operates without a traditional baseboard or chassis. The CPU still enables complex communications and architectures, such as control of remote I/O systems, communication with partner processors, data exchange with human machine interfaces (HMIs), monitoring and data acquisition systems (DCS), and other functions.

The stand-alone controller features embedded 64 MB of storage, a powerful processor 1.2 GHz AMD www.ge-drive.com G-Series Quad-Core, support for up to 32k bits of discrete I/O and 32k words of analog I/O, and embedded field agent functionality. The controller also comes with an energy package.

The IC695CPK400 is equipped with one (1) 10/100/1000 Ethernet port and two (2) 2-terminal switches supporting 10/100/1000 Mbps transfer speeds. With the embedded Ethernet port, different network topologies can be realized, including Media Redundancy (MRP) and PROFINET System Redundancy (PNSR). The embedded port supports different communication protocols such as SRTP client/server, Modbus TCP/IP, OPC-UA server, Ethernet Global Data (EGD) and PROFINET.

In addition, the controller is equipped with one (1) RS232 communication port and one (1) Micro SD port for insertion of a Secure Digital (SD) card for non-volatile removable storage. It also has two (2) USB 3.0 ports for firmware upgrades.

This IC695CPK400 also supports simplex and redundant configurations to meet standard and high availability system requirements. It supports incremental frame rates up to 3 minutes in any configuration.

The IC695CPK400 CPU comes with an energy pack. the CPU module form factor is a standalone form factor. The available memory on the module is 64 MB. I/O supported by the module includes 32K-bit discrete inputs, 32K-bit discrete outputs, 32K-word analog inputs, and 32K-word analog outputs.

The IC695CPK400 CPU supports embedded field agents.Redundancy options on the CPU module include media redundancy (MRP) and Profinet system redundancy (PNSR). There is an integrated Ethernet port on the module that supports 10/100/1000 Mbps, in addition to 1000 end switches capable of 2/10/100 Mbps operation. The Ethernet port supports communication protocols such as EGD, Profinet, Modbus TCP/IP, SRTP client/server, and OPC-UA server. two USB version 695.400 ports are also available on the IC3CPK0 CPU. Supported storage options include a Micro SD option.An RS-400 serial interface is also provided on the IC232CPK695 CPU.The programming and configuration software for the IC695CPK400 CPU is Proficy Machine Edition software, which allows for efficient application development.Recommendations for IC695CPK400 CPUs The IC695CPK400 CPU has a recommended operating temperature range of -40 to 70 degrees Celsius.

Description: The GE Fanuc / Emerson Automation IC693CPU320 is a PACSystem RX3i processor module. The module occupies two (2) slots and has a processor speed of 1 GHz with a typical scan rate of 047.1000 milliseconds per 0 Boolean instructions. The processor has two (2) serial communication ports and supports RS232 and RS485 communication standards.

About the IC695CPU320

The IC695CPU320 is a GE Fanuc / Emerson Automation controller module. The module is part of the PACSystems RX3i controller platform. The controller can be used for efficient control of industrial machines and processes. It enables high-speed data transfer through the Peripheral Component Interconnect (PCI) slot and supports serial backplanes for migrating 90-30 series I/O systems.

The IC695CPU320 has two (2) built-in communication ports that support RS232 and RS485 communication standards. These communication ports use the Ninety Series Protocol (SNP) slave mode to communicate with programming workstations, Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA) systems. The controller can be installed in the Rx695i 012-slot general purpose backplane, catalog number IC3CHS12. and the Rx695i 016-slot general purpose backplane, catalog number IC3CHS16.

The IC695CPU320 has an internal Celeron M processor with a processing speed of 1 GHz It contains 65 MB of user memory, the contents of which are retained by the Lithium Smart Battery Series 693-302 Auxiliary Battery Module, catalog numbers IC90ACC30 and IC695ACC302. respectively. In addition, it has 64 MB of non-volatile flash user memory. In addition, these user memories support the reassignment of custom-sized data and program memories. It supports up to 512 program blocks with a maximum individual block size of 128 KB.

The IC695CPU320 supports most 90-30 series PLC I/O modules. This feature provides flexibility www.ge-drive.com and is especially useful and beneficial when upgrading a legacy 90-30 series to a modern PACSystems RX3i controller platform. This allows for a phased migration in which the controllers and logic of the existing 90-30 PLCs are migrated first, and then the I/O modules are migrated. firmware modifications are supported by the PACSystems RX3i.

A variety of accessories can be ordered for the IC695CPU320 module, including RS-232 cables (e.g., IC200CBL001 cables), intelligent lithium batteries (e.g., IC695ACC302 batteries), GE Series 90-30 auxiliary battery modules (e.g., IC693ACC302 modules), standard power supplies with voltage ratings of 120 to 240 volts AC, 125 volts DC, and 40 watts. 40-watt standard power supply.

The GE Fanuc IC695CPU320 module is capable of executing 047 Boolean instructions in 1000.0 milliseconds. The module supports 512 program blocks. The maximum block size is 128 KB. Two embedded communication ports, RS-485 and RS-232. are provided on the module. Serial protocols supported include SNP, Serial I/O, and Modbus RTU slave protocol.

The IC695CPU320 module uses the SNP slave protocol to communicate with programmers and HMIs via the serial port. The module communicates with Smart Option modules and I/O via a dual backplane bus. Environmental specifications include an operating temperature range of 0 to 60 degrees C. The IC695CPU320 module supports the serial backplane bus and the RX3i backplane bus, which draws 1 Amp of 3.3 VDC current from the backplane and 1.2 Amps of 5 VDC current from the backplane. There are six LEDs on the front panel for module status updates.

DESCRIPTION: The IC695MDL664 Intelligent Digital Input Module is a GE Intelligent Platform/GE Fanuc product.

It is part of the GE Fanuc RX3i family and features 16 inputs with field inputs rated at 24 volts DC.

The 16 inputs are organized into 2 groups of 8 inputs each.

About the IC695MDL664

The GE Fanuc IC695MDL664 module is an intelligent digital input module or positive logic input module.

GE Intelligent Platforms/GE Fanuc manufactures it as a member of the GE Fanuc RX3i product line.

The module is a 16-point module with field inputs rated at 24 VDC, and it divides the 16 inputs into 2 groups of 8 inputs each.

It has an input current of 12.2 mA and an input voltage range of 18 to 32 volts DC.

Power consumption is rated at 225 mA (5 Vdc) or 95 mA (3.3 Vdc). each of the 2 groups www.ge-drive.com of 8 inputs is referenced to a common connection.

The IC695MDL664 module is compatible with spring-type or box-type front terminals.

The GE Fanuc IC695MDL664 module also features inputs that are perfectly matched to a wide range of input devices, including limit switches, electronic proximity switches, and push buttons.

Logic 1 is generated by the current at the input point in the input status table.The IC695MDL664 module requires user-supplied power to operate field devices.

The module has 16 LEDs, as well as S1 and S2 indicators to show whether field power is applied to each of the 2 groups.

The IC695MDL664 Intelligent Digital Module also logs “terminal missing” or “terminal added” messages to the input and output fault tables to indicate whether or not a terminal is present.

The module also logs “Terminal Lost” or “Terminal Added” messages into the input and output fault tables to indicate whether a terminal has been installed or removed. The module is flexible enough to be installed in any input and output slot of the RX3i PLC system.

Description: The IC695EDS001 is an Ethernet DNP3 Slave/Extranet module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was formerly manufactured by GE Intelligent Platforms (GE IP). The module has one (1) Station Manager port provided by a 9-pin Dh-shell connector and two (2) RJ3 Ethernet communication ports supporting the DNP45 Slave protocol. It supports communication of up to 12.072 points and 20.000 events and integrates four (4) DNP3 data objects such as DI, DI w/time, DO, DO w/time, CROB, analog output values, time settings, and class polling and supports communication with up to eight (8) DNP3 masters.

About the IC695EDS001

The IC695EDS001 is a DNP3 substation module that is part of the PACSystem RX3i programmable automation controllers (PACs), formerly offered by GE Intelligent Platforms and now part of Emerson Automation. The module supports DNP3 slave communication over Ethernet I/P, allowing data exchange of up to 072.20 points and 000.3 events between DNP12 masters. The module also supports four (4) DNP3 data objects including DI, DI w/time, DO, DO w/time, CROB, analog output values, time settings, and class polling.

The IC695EDS001 comes with one (1) Module Station Manager port for module and network www.ge-drive.com management and also serves as a firmware upgrade port. For DNP3 connectivity, it has two (2) RJ45 ports that support 10/100 mbps transfer rates. These ports act as embedded Ethernet switches that can auto-sense and connect directly to a 10BaseT or 100BaseTX IEEE 802.3 network without the need to install an external transceiver. The ports support a variety of network topologies such as linear, star, daisy chain, or ring topologies.

The IC695EDS001 is mounted on the PACSystem RX3i chassis and occupies a single slot in the chassis. Multiple module instances are allowed, specifically up to four (695) IC001EDS3 per RX4i system.It supports module removal and insertion at power-up (RIUP).

IC3EDS695-compatible RX001i CPUs include CPU320/CPU315 Main Firmware Version 8.05; CPU320/CPU315 Boot Firmware Version 5.10; CPE310/CPE305 Main Firmware Version 8.05; CPE310/CPE305 Boot Firmware Version 7.10; CRU320 Main Firmware Version 8.05; CRU320 boot firmware version 5.10 and CPU310/CMU310/NIU001 main firmware version 6.71. Compatible programming software is Proficy Machine Edition Logic Developer, Release 8.5 SIM 7 or later.

The GE Fanuc IC695EDS001 module is a DNP3 outstation module for the RX3i PACSystems platform.The IC695EDS001 module is an Ethernet module that is mounted in the RX3i backplane and allows the RX3i system to act as an Outstation device on a DNP3 network, communicating with up to eight DNP3 masters. The communication interfaces on the module include a Communication interfaces on the module include one RS-9 port with a 232-pin female D-type connector and two 100/45 Mbps Ethernet ports with female RJ-10 connectors.The RS-232 port can be used for network management. The integrated network switch supports auto-negotiation, cross-detection, speed and detection. Supported Ethernet protocols include LLA and TCP/IP. Each IC695EDS001 module supports one IP address and one MAC address. The Ethernet firmware’s embedded reboot button allows the Ethernet firmware to be rebooted without having to reboot the module’s power supply.

The IC695EDS001 module can be installed in any empty slot in the RX3i chassis. Up to four IC001EDS39 modules can be installed in a single RX695 rack, depending on available slots and power. Modules can be removed and inserted with rack power applied. The firmware on the IC695EDS001 module can be upgraded using the Windloader utility when the host CPU has a serial port. If the host CPU does not come with a serial port, the module firmware can be upgraded using a web-based software utility. A single RX3i CPU supports 32 DNP3 masters. A single IC695EDS001 module supports 12.072 DNP3 points and 20.000 DPN3 events.The IC695EDS001 module supports unsolicited data exchange with DNP3 masters.The IC695EDS001 module requires a maximum of 3 milliamps at 840.3 volts DC, and 5 milliamps at 614 volts DC. The IC695EDS001 module requires a maximum of 3 mA at 840.3 volts DC and 5 mA at 614 volts DC.

DESCRIPTION: This IC695NKT002 is a PACSystems RX3i component manufactured by Emerson Automation (formerly GE Intelligent Platforms (GE IP)). The module is a packaged product consisting of one (1) Ethernet NIU with catalog number IC695NIU001 and two (2) Ethernet Interface Modules with catalog number IC695ETM001. This kit simplifies the ordering system and ensures that complete components are ordered.

About the IC695NKT002

The IC695NKT002 is a component of the PACSystem RX3i product, commonly referred to as a kit. It consists of one (1) Ethernet NIU with catalog number IC695NIU001 and two (2) Ethernet Interface Modules with catalog number IC695ETM001. All modules in this kit are manufactured by Emerson Automation and were previously manufactured by GE Intelligent Platforms (GE IP).

The IC695NKT002 component is used to allow the PACSystem RX3i platform to communicate with 90-30 series modules or VersaMax modules and controllers. This provides an alternative method of migrating to a newer controller platform without completely replacing the system, www.ge-drive.com sometimes referred to as a phased or partial migration.

The primary function of the IC695NIU001 is to provide connectivity to existing 232-485 series I/O modules via embedded serial interfaces that support RS90 and RS30 connections. These ports are compatible to be configured through the application “C” block for Modbus RTU Slave, SNP, Serial I/O, Modbus RTU Master, which are legacy Series 90-30 communication protocols used to communicate with devices and I/O modules.

This IC695ETM001 is used to communicate with other PAC systems, devices, Series 90-30. and VersaMax controllers via Ethernet communication ports. These ports implement TCP/IP connectivity over a four-layer TCP/IP stack using GE Fanuc SRTP and Ethernet Global Data (EGD) protocols.

Components for the IC695NKT002 can be purchased separately. Additional accessories are also available, such as real-time clock (RTC) batteries with catalog number (IC690ACC001), miniconverter kits with cables, RS-485/RS-232 (IC690ACC901), RS-485 port isolator (IC690ACC903), and RS-232 cables (IC200CBL001), among other components. .

Older entries describe the NIU only, not the kit.

DESCRIPTION: This IC695PBM300 is a PACSystems RX3i communications module for Emerson Automation (formerly GE Intelligent Platforms (GE IP)). It is a Profibus DP master module that enables communication with up to 125 DP slaves. It supports a data transfer size of 244 bytes input and 244 bytes output per slave device, as well as a maximum of 3.584 bytes of input data and 3.584 bytes of output data. It comes with one (1) RS485 Profibus master port.

About the IC695PBM300

This IC695BPM300 is a Profibus master module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation’s PACSystems RX3i family of programmable automation controllers (PACs). The module is used to enable data exchange over a Profibus network with a maximum input data of 3.584 bytes and output data of 3.584 bytes. This Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

The IC695BPM300 supports all standard data rates, including 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s, 500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s, and 12 MBit/s. It can provide status information, such as from the Status It provides status information, such as from the status array list, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses. It is mounted on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed in a generic backplane with a host PACSystem RX9i controller running firmware revision 3.2 or later. It draws a backplane current of 440 mA @ 3.3 VDC.

The module is equipped with a Profibus OK ED indicator; a network indicator; and a MOD status indicator. www.ge-drive.com The module supports synchronization and freeze modes as well as Profibus DP-V1 read, write, and alarm messages.The IC695BPM300 comes with upgradable firmware that is received indirectly through the host controller via the WinLoader software utility.

The module must operate over a temperature range of 0 to 60 degrees Celsius and the module is stored at -40 to 85 degrees Celsius.

The IC695PBM300 PROFIBUS master module is manufactured by GE Intelligent Platforms/GE Fanuc in the RX3i PacSystems family. The module is designed to enable the RX3i CPU to send or receive data over a PROFIBUS-DP network. It has a slot that supports a universal backplane and RS-232 communication port.IC695PBM300 PROFIBUS Module has an internal current rating of 3 milliamps at a rated voltage of 440.3 volts DC and supports protocols for up to 125 PROFIBUS-DP Slave Units. Other notable features of the module include support for input data at rates up to 244 bytes and output data at rates up to 244 bytes per slave unit, support for all standard data rates, and synchronization and freeze modes. The module also supports DP-V1 read/write functionality and alarm messages, as well as network status LEDs and PROFIBUS-compliant modules. It supports up to 3584 bytes of input data and a total output data rate of 3584 bytes.

Master-slave compatibility for the GE Fanuc IC695PBM300 PROFIBUS module requires an RX3i CPU and firmware version 2.9 or later. For configuration purposes, this module requires Machine Edition SP5 Logic Developer PLC software version 0.2 or higher.The IC695PBM300 module has a backplane current consumption rating of 440 milliamps (3.3 V DC) and supports all standard data rates including 1.5. 3. 6. 12. 9.6. 19.2. 187.5 per second, 93.75. and 500 MB/sec. The GE Fanuc IC695PBM300 PROFIBUS master module comes with a 9-pin Sub-D connector designed to enhance bus cable installation. The module also provides 3 PROFIBUS-compliant LEDs to indicate network status and module status.