News

Features:

6 serial I/O ports

Supports synchronous and asynchronous communication

128 Kb of dynamic RAM

High-speed bi-directional DMA on two channels

The Motorola MVME333S-2 is a VMEbus intelligent communications controller with six serial I/O www.ge-drive.com ports that can be configured for synchronous or asynchronous and RS-232C or RS-422 electrical protocols.

On-board intelligence includes the MC68010 10 MHz CPU with two slots for firmware and 128 Kb of dynamic RAM for data buffering.

It has firmware for asynchronous protocols on all six channels (up to 9600 baud in both directions on all channels simultaneously).

In addition, there is a high-speed bi-directional DMA for synchronous protocols up to 1 Mb/s on two channels.

MVME330

Provides a high-performance 10 Mbps Ethernet interface with MC68000MPU, MK68590LANCE Ethernet controller, AM7991 Seria!1/0 adapter, and on-board EPROM with power-on self-test routines and kernel software for data rates up to 200 1 Kbytepackets/sec.

MVME331

VMEbus intelligent communications controller with six serial l/0 ports configurable as synchronous or asynchronous, and RS232C or RS-422 electrical protocols. The module also comes with firmware to implement synchronous protocols on all six channels (all channels simultaneously in both directions up to 9600 baud).

MVME332

8-channel intelligent serial communication controller for synchronous and asynchronous communication (RS232C). The module contains the MC68010 and 128K bytes of dynamic RAM, expandable to 512K.

MVME333

Same as the MVME331. but with the addition of high-speed bi-directional DMA on two channels for high-speed (up to 1Mb/sec) synchronous protocols, i.e., X.25 packet-switched networks.

MVME340

The VMEbus Parallel I/O module provides 64 parallel I/O lines: three 24-bit timers; three interrupters; one 32-bit and one 16-bit data channel, or any combination of 16-bit and 8-bit data channels; and 4GB, 16Mb, or 64Kb address ranges.

MVME350

Intelligent Streaming Media Tape Controller Module, M68010 processor-based, 128KB on-board RAM, QlC-02 interface: firmware installed.

MVME390

Color Graphics Controller Module, 1K x 1K Dual-Port Display Memory, Eight Colors in 4096 Palette (3 pIanes), TTL RS170/RS343A: RGB Output, 50/60 Hz Screen Refresh Non-Interlaced.

MVME700

Transition and Mass Storage

l/O transition module, double-height 80 mm Eurocard format, wrap-around board.

MVME701

l/O Transition Module Dual height 80 mm Eurocard, DlN to DB25 and 50-PiN dual row headers provide connectors for the MVME050 serial and parallel ports; and a battery backup (user-installed) for the MVME050 Daytime Clock.

MVME702

Provides Winchester cable termination logic. Provides Winchester cable termination logic.

MVME7O5

I/O conversion module doubleie-high80m:nEurocard format or six-channel serial transceiver module, each channel can be independently configured to RS-2320 or RS-422 standards, with on-board sockets provided for plugging in RS-232C or RS-422 driver and receiver devices which are supplied with the module to provide free space for the user.

MVME706

Same as MVME705 but all channels are now RS-232C compliant.

MVME707

MVME130 RS-232C Power Distribution Board with RS.232C serial l/0 cable assembly. Designed to interface with the MVME130/131.

Features:

4 25-pin multi-protocol EIA-232-D serial ports

The MVME712M is an I/O converter module for Motorola MPU VME Modules, VME Processor Modules, Embedded Controllers, and Single Board Computer (SBC) series processor modules.

The MVME712M is compatible with the MVME147. MVME1600. MVME162. MVME2600. MVME167. MVME2700. MVME177. MVME3600. MVME4600.

The MVME712M is used as an interface between the processor module and its peripherals. The purpose of this module is to provide rear panel industry standard connectors to simplify external customer cable requirements.

The P2 adapter assembly routes I/O signals and ground from the P2 connector on the chassis backplane (at the VMEmodule MPU connection) to the MVME712M.

The MVME712M routes signals to four serial ports that have four industry-standard DB-25 connectors on the front panel.

The serial ports can be configured as EIA-232-D DTE or DCE via a www.ge-drive.com patch cable arrangement on the MVME 712M.

The MVME712M also has an Ethernet port, a SCSI port, and a printer port on the front panel.

In addition, the MVME712M routes EIA-232-D Port 2 signals to the internal modem.

The MVME712M requires the use of the P2 adapter board, which is not included.

The features of the P2 adapter board include:

-Connectors that allow SCSI cables to be connected to other SCSI devices and/or to the MVME712M via a flat ribbon cable.

-SCSI termination resistors mounted in sockets for cable ends or in the middle of the cable configuration.

-Terminator power developed from +5 Vdc on connector P2 on P2 adapter, and fuses (2 A) on P1 adapter

-Connects EIA-232-D port, printer port, SCSI and Ethernet signals to MVME712M connectors

PPMC750-2xxx Description

The PPMC750-2xxx is an extended form factor version of the PPMC750 Processor PCI Mezzanine Card (PPMC) board (see the Processor PMC Standard for VITA-32-199x Processor PCI Mezzanine Cards for more information).

The PPMC750-2xxx is 1.5 times wider than normal at 111 mm. It is based on the PowerPC MPC750 processor and the Hawk PCI host bridge/system memory controller.

Standard features of the PPMC750 include 1MB of L2 cache, an on-board bank of SDRAM (32MB to 128MB), 8MB of FLASH, and optional SDRAM memory expansion.

In addition to the standard features of the PPMC750. the PPMC750-2xxx features 1MB of socketed FLASH, a 10/100TX Ethernet channel, a 190-pin Mictor debug connector, and a serial port debug connector.

Four 64-pin PMC connectors on the PPMC750-2xxx are used to connect the PPMC750-2xxx to the motherboard.

A 10-pin right-angle connector located on the side of the motherboard provides the interface to the asynchronous serial port. A 16-pin header provides the interface to the processor’s JTAG/COP port.

A 190-pin Mictor connector on the secondary side of the board provides debug www.ge-drive.com access to the processor bus.

The serial port and JTAG/COP interfaces and ABORT_L signals are also routed to the PMC P14 connector for access to the carrier board.

The PPMC750-2xxx includes a 140-pin AMP connector mounted on the auxiliary side of the board to provide sockets for memory expansion functions.

The presence of this connector increases the height measurement of the components on both sides beyond the standard PMC height.

Monarch and Non-Monarch PPMC

The traditional concepts of host/master and slave/target processors changed with the creation of the PPMC because the arbiter or clock source traditionally located on the host board was not on the PPMC7502xxx.

The VITA 32 specification defines the terms Monarch and Nonmonarch to refer to the two modes of PPMC operation.

Monarch PPMC is defined as the master PCI bus PPMC (or CPU) that performs PCI bus enumeration at power-up or reset and acts as a PCI interrupt handler.

A non-Monarch type is a slave/target processor that does not perform bus enumeration and does not handle PCI interrupts, but may issue PCI interrupts to the host processor.

A system may have a Monarch PPMC750-2xxx and/or one or more non-Monarch PPMC750-2xxx, resulting in a loosely coupled multiprocessing system.

A PPMC750-2xxx operating as a Monarch system may be connected to a carrier board with slave processors, PCI and other I/O devices.

The PPMC750-2xxx operating as a non-monarch system can be mounted on a carrier board with a master processor and other PCI devices such as MVME2400 or MCPN750 boards.

PPMC750-2xxx boards running in non-monarch mode may require a different version of PPCBUG or other operating system than PPMC750-2xxx boards running in monarch mode.

The PPMC750-2xxx software is configured for Monarch or Non-Monarch mode by reading the status of the MONARCH# pin on the PPMC750-2xxx.

This pin is grounded or open on the carrier board to enable the desired mode of operation. Refer to the MONARCH# signal description on page 3-14 of this manual for details.

Carrier Board Requirements The carrier board must provide standard PCI interfaces including 3.3V and 5V power, PCI address/control, PCI clock, and PCI arbiter REQ/GNT pairs.

Refer to the VITA-32-199x specification. The carrier board must also have the MONARCH# pin grounded to enable Monarch operation mode.

Turning the MONARCH# pin on will enable non-Monarch mode.

System Enclosure

System enclosure requirements depend on the configuration and architecture of the baseboard (VME, CompactPCI, or custom), and two slots are required for both the baseboard and the attached PPMC7502xxx (in a VME or CompactPCI chassis).

The MVME162FX is based on the MC68040 or MC68LC040 microprocessor.

Different versions of the MVME162FX are available with 4MB, 8MB or 16MB of unprotected DRAM, 8KB SRAM (with battery backup), daily clock (with battery backup),

Ethernet transceiver interface, two serial ports with EIA-232-D or EIA-530 or EIA-485/422 interfaces, six timers, watchdog timer, one PROM socket,

1MB of Flash memory (one Flash device), four IndustryPack (IP) interfaces with DMA, SCSI bus interface with DMA, VMEbus controller, and 512KB of SRAM with battery backup. a “no VMEbus” option is also available.

The I/O on the MVME162FX is connected to the VMEbus P2 connector. The main board is connected via a P2 transition board and a cable connecting the transition board.

The MVME162FX supports the transition boards MVME712-12. MVME712-13. MVME712M, MVME712A, MVME712AM, and MVME712B (referred to in this manual as MVME712x unless otherwise noted).

The MVME712x transition board provides configuration headers and industry standard connectors for I/O devices.

I/O connections to the serial ports on the MVME162FX are also made via two DB-25 front panel I/O connectors.

The MVME712 series transition boards are designed to support the MVME167 www.ge-drive.com boards, but can be used on the MVME162FX if some special precautions are taken.

(For more information, see the Serial Communications Interfaces section of the MVME162FX Embedded Controller Installation and Use Manual).

These transition boards These transition boards provide configuration headers, serial port drivers, and industry-standard connectors for I/O devices.

These transition boards provide configuration headers, serial port drivers, and industry standard connectors for I/O devices.

Benefits

The MVME162FX series provides an ideal platform for embedded monitoring applications for OEMs and solution developers.

It enables OEMs to minimize engineering costs while integrating value-added hardware and software applications into off-the-shelf products.

To provide a wide range of solutions, the MVME162FX allows the use of a variety of MPUs, memory and interface options such as floating point, Ethernet, SCSI and VME.

As a result, the MVME162FX variants best fit the application requirements.

Functional Features

– Optional Processor:

– 32 MHz MC68040 Enhanced 32-bit Microprocessor with 8KB Cache and MMU and FPU

– 25 MHz MC68LC040 Enhanced 32-bit Microprocessor with 8KB Cache and MMU

– A32/D64 VMEbus Master/Slave Interface with System Controller Function

– High performance DMA support for VMEbus D64 and local bus memory burst cycles

– 4. 8 or 16MB of shared DRAM

– 512KB SRAM with battery backup

– 1MB Flash for on-board monitor/debugger or user-installed firmware

– 8K x 8 NVRAM and time clock with battery backup

– Two serial communication ports, console port is EIA-232-D DCE, second port is user configurable to EIA-232-D/EIA-422 (V.36) DTE/DCE

– Four 16-bit or two 32-bit IndustryPack® ports, one DMA channel per port

– Six 32-bit timers (four without VMEbus) and watchdog timer

– Optional SCSI bus interface with 32-bit local bus burst DMA

– Optional Ethernet transceiver interface with 32-bit local bus DMA

– One 32-pin PLCC EPROM socket

– Four-stage requester, seven-stage interruptor, and seven-stage interrupt handler for VMEbus

– Remote reset/pause/status control functions

– On-board debugger and diagnostic firmware

Motorola Commitment

Motorola Computer Group is committed to delivering best-in-class embedded computing solutions.

The MVME162FX family reinforces this commitment by providing superior hardware at a low price.

The MVME162FX family reinforces this commitment by providing superior hardware, affordable performance, and staying true to the principles of open computing:

modularity, scalability, portability and interoperability.

Motorola Computer Group is ISO9001 certified and offers world-class quality in manufacturing, engineering sales and marketing.